Wave Propagation Scattering due to Defects on Thin Composite Plates
DOI:
https://doi.org/10.15282/jmes.5.2013.6.0057Keywords:
SHM, wave propagation, wavelet analysis, Gl/epoxy composites.Abstract
Engineering structures which are based on laminated composites have a high probability of unexpected damage developing during service. The damaged formations must be monitored from the beginning before they head towards structural failure which could result in substantial damage. This leads to the necessity of a structural health monitoring (SHM) system to be installed during the construction of laminated composite structures. However, an understanding of damage area detection and damage characteristics is essential before a SHM system can be integrated into the structures. This article presents the effects of wave propagation through an existing area of damage on composite plates. Theoretically, a propagating wave that starts from any source will vary when crossing an area with damage. This study shows that high frequency wave propagation (kHz range) reacts differently when passing through the damaged area, compared with low frequency wave propagation. The results of the study will lead to an effective damage detection method, utilizing the available vibration source, especially for the condition monitoring of thin laminated composite structures.
References
Adebisi, A. A., Maleque, M. A., & Rahman, M. M. (2011). Metal matrix composite brake rotor: Historical development and product life cycle analysis. International Journal of Automotive and Mechanical Engineering, 4, 471-480.
Bhaskar, H. B., & Sharief, A. (2012). Effect of solutionizing on dry sliding wear of al2024-beryl metal matrix composite. Journal of Mechanical Engineering and Sciences, 3, 281-290.
Chui, C. K. (1992). An introduction to wavelets (Vol. 1): Academic press.
Croxford, A., Wilcox, P., Drinkwater, B., & Konstantinidis, G. (2007). Strategies for guided-wave structural health monitoring. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Science, 463(2087), 2961-2981.
Diamanti, K., & Soutis, C. (2010). Structural health monitoring techniques for aircraft composite structures. Progress in Aerospace Sciences, 46(8), 342-352.
Hamstad, M., O‘GALLAGHER, A., & Gary, J. (2002). A wavelet transform applied to acoustic emission signals: Part 2: Source location. Journal of Acoustic Emission, 20, 62-82.
Ibrahim, M. S., Sapuan, S. M., & Faieza, A. A. (2012). Mechanical and thermal properties of composites from unsaturated polyester filled with oil palm ash. Journal of Mechanical Engineering and Sciences, 2, 133-147.
Jingpin, J., Bin, W., & Cunfu, H. (2008). Acoustic emission source location methods using mode and frequency analysis. Structural Control and Health Monitoring, 15(4), 642-651.
Kahandawa, G. C., Hafizi, Z. M., Epaarachchi, J., & Lau, K. T. (2012, Dec.9–12). Detecting delamination in a composite structure using an embedded fbg – ae hybrid system. Paper presented at the 7th Australasian Congress on Applied Mechanics (ACAM 7), Adelaide, Australia.
Lam, P.-M., Lau, K.-T., Ling, H.-Y., Su, Z., & Tam, H.-Y. (2009). Acousto-ultrasonic sensing for delaminated gfrp composites using an embedded fbg sensor. Optics and lasers in engineering, 47(10), 1049-1055.
Lin, J. (2001). Feature extraction of machine sound using wavelet and its application in fault diagnosis. NDT & E International, 34(1), 25-30.
Mal, A., Ricci, F., Banerjee, S., & Shih, F. (2005). A conceptual structural health monitoring system based on vibration and wave propagation. Structural Health Monitoring, 4(3), 283-293.
Muravin, B., Muravin, G., & Lezvinsky, L. (2010). The fundamentals of structural health monitoring by the acoustic emission method. Paper presented at the Proceedings of the 20th International Acoustic Emission Symposium, November.
Orifici, A., Herszberg, I., & Thomson, R. (2008). Review of methodologies for composite material modelling incorporating failure. Composite Structures, 86(1), 194-210.
Popovics, J. S. (2009). Recent developments in ndt and shm in the united states. Non-Destructive Testing in Civil Engineering, NDTCE, 9.
Shan, C. W., Ghazali, M. I., & Idris, M. I. (2013). Improved vibration characteristic of flexible polyurethane foam via composite formation. International Journal of Automotive and Mechanical Engineering, 7, 1032-1042.
Simonovski, I., & Boltežar, M. (2003). The norms and variances of the gabor, morlet and general harmonic wavelet functions. Journal of Sound and Vibration, 264(3), 545-557.
Umar, A. H., Zainudin, E. S., & Sapuan, S. M. (2012). Effect of accelerated weathering on tensile properties of kenaf reinforced high-density polyethylene composites. Journal of Mechanical Engineering and Sciences, 2, 198-205.
Zohari, M. H., Epaarachchi, J. A., & Lau, K. (2013). Modal acoustic emission investigation for progressive failure monitoring in thin composite plates under tensile test. Key Engineering Materials, 558, 65-75.
