Effect of filler loading on mechanical properties of pultruded kenaf fibre reinforced vinyl ester composites

A.M. Fairuz; S.M. Sapuan; E.S. Zainudin; C.N.A. Jaafar

doi:10.15282/jmes.10.1.2016.16.0184

Authors

A.M. Fairuz Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor, Malaysia
S.M. Sapuan Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor, Malaysia
E.S. Zainudin Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor, Malaysia
C.N.A. Jaafar Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor, Malaysia

DOI:

https://doi.org/10.15282/jmes.10.1.2016.16.0184

Keywords:

Pultrusion; filler loading; vinyl ester; natural fibre composites; mechanical properties.

Abstract

Pultrusion is one of the polymer composite fabrication processes employing a combination of pulling and extrusion processes. The composite profiles are obtained by pulling resin-impregnated fibres through a series of heated dies. The ability of the pultrusion technique to support a high volume of fibre fraction produces the high stiffness of the composite profile. There are many parameters such as filler loading, mould temperature and pulling speed to be considered and controlled during the pultrusion process. In this paper, an investigation of the effect of the filler loading on the tensile and flexural properties of the pultruded kenaf reinforced vinyl ester composites is presented. As the filler loadings were increased to a significant amount, the mechanical properties started to drop, which was attributed to the increase of viscosity in the matrix and in turn the increase in porosity and decrease in the wettability of the composites. Hence, increasing the amount of filler loading increased the tensile and flexural properties of the pultruded composites in terms of strength and stiffness. The tensile properties of the composites had increased by up to 50% of fibre loading. The maximum flexural strength and modulus were obtained at 30 and 50% of filler loadings respectively. The maximum compressive strength was observed to take place at 40% of filler loading.

References

Sastra H, Siregar J, Sapuan SM, Hamdan M. Tensile properties of Arenga pinnata fiber-reinforced epoxy composites. Polymer-Plastics Technology and Engineering. 2006;45:149-55.

Rashdi A, Sapuan S, Ahmad M, Khalina A. Water absorption and tensile properties of soil buried kenaf fibre reinforced unsaturated polyester composites (KFRUPC). Journal of Food, Agriculture & Environment. 2009;7:0.

Leman Z, Sapuan SM, Azwan M, Ahmad MMHM, Maleque M. The effect of environmental treatments on fiber surface properties and tensile strength of sugar palm fiber-reinforced epoxy composites. Polymer-Plastics Technology and Engineering. 2008;47:606-12.

Abdul Majid MS, Daud R, Afendi M, Amin NAM, Cheng EM, Gibson AG, et al. Stress-strain response modelling of glass fibre reinforced epoxy composite pipes composites under multiaxial loadings. Journal of Mechanical Engineering and Sciences. 2014;6:916-28.

Nosbi N, Akil HM, Ishak ZM, Bakar AA. Degradation of compressive properties of pultruded kenaf fiber reinforced composites after immersion in various solutions. Materials & Design. 2010;31:4960-4.

Sharma D, McCarty T, Roux J, Vaughan J. Fluid mechanics analysis of a two‐ dimensional pultrusion die inlet. Polymer Engineering & Science. 1998;38:1611- 22.

Fairuz A, Sapuan S, Zainudin E, Jaafar CNA. Optimization of pultrusion process for kenaf fibre reinforced vinyl ester composites. Applied Mechanics and Materials: Trans Tech Publ; 2015. p. 499-503.

Song YS, Youn JR, Gutowski TG. Life cycle energy analysis of fiber-reinforced composites. Composites Part A: Applied Science and Manufacturing. 2009;40:1257-65.

Fatchurrohman N, Sulaiman S, Sapuan SM, Ariffin MKA, Baharuddin BTHT. Analysis of a metal matrix composites automotive component. International Journal of Automotive and Mechanical Engineering. 2015;11:2531-40.

Wan Dalina WAD, Mariatti M, Mohd Ishak ZA, Mohamed AR. Comparison of properties of MWCNT/carbon fibre/ epoxy laminated composites prepared by solvent spraying method. International Journal of Automotive and Mechanical Engineering. 2014;10:1901-9.

Othman RN, Wilkinson AN. The impedance characterization of hybrid cnt-silica epoxy nanocomposites. International Journal of Automotive and Mechanical Engineering. 2014;10:1832-40.

Zamri MH, Md Akil H, Mohd Ishak Z, Abu Bakar A. Effect of different fiber loadings and sizes on pultruded kenaf fiber reinforced unsaturated polyester composites. Polymer Composites. 2015;36:1224-9.

Akil HM, Cheng LW, Ishak ZM, Bakar AA, Rahman MA. Water absorption study on pultruded jute fibre reinforced unsaturated polyester composites. Composites Science and Technology. 2009;69:1942-8.

Akil HM, De Rosa IM, Santulli C, Sarasini F. Flexural behaviour of pultruded jute/glass and kenaf/glass hybrid composites monitored using acoustic emission. Materials Science and Engineering: A. 2010;527:2942-50.

Omar MF, Akil HM, Ahmad ZA, Mazuki A, Yokoyama T. Dynamic properties of pultruded natural fibre reinforced composites using Split Hopkinson Pressure Bar technique. Materials & Design. 2010;31:4209-18.

Coelho R, Calado V. An optimization procedure for the pultrusion process based on a finite element formulation. Polymer Composites. 2002;23:329-41.

Masouras K, Silikas N, Watts DC. Correlation of filler content and elastic properties of resin-composites. Dental Materials. 2008;24:932-9.

Fu S-Y, Feng X-Q, Lauke B, Mai Y-W. Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate– polymer composites. Composites Part B: Engineering. 2008;39:933-61.

Fairuz A, Sapuan S, Zainudin E, Jaafar C. Polymer composite manufacturing using a pultrusion process: a review. American Journal of Applied Sciences. 2014;11:1798.

Bassam F, York P, Rowe R, Roberts R. Young's modulus of powders used as pharmaceutical excipients. International Journal of Pharmaceutics. 1990;64:55- 60.

Bhattacharya M, Bhowmick AK. Polymer–filler interaction in nanocomposites: new interface area function to investigate swelling behavior and Young's modulus. Polymer. 2008;49:4808-18.

Qiang F. Effect of morphology on brittle-ductile transition of HDPE/CaCO3 blends. Journal of Applied Polymer Science. 1993;49:673-7.

Nurdina A, Mariatti M, Samayamutthirian P. Effect of single‐mineral filler and hybrid‐mineral filler additives on the properties of polypropylene composites. Journal of Vinyl and Additive Technology. 2009;15:20-8.

Zhou B, Ji X, Sheng Y, Wang L, Jiang Z. Mechanical and thermal properties of poly-ether ether ketone reinforced with CaCO 3. European Polymer Journal. 2004;40:2357-63.

Fuad M, Hanim H, Zarina R, Ishak ZM, Hassan A. Polypropylene/calcium carbonate nanocomposites—Effects of processing techniques and maleated polypropylene compatibiliser. eXPRESS Polym. eXPRESS Polymer Letters. 2010;4:611-20.

Hanim H, Zarina R, Fuad MA, Mohd Z, Ishak AH. The effect of calcium carbonate nanofiller on the mechanical properties and crystallisation behaviour of polypropylene. Malaysian Polymer Journal. 2008;3:38-49.

Jiang L, Lam Y, Tam K, Chua T, Sim G, Ang L. Strengthening acrylonitrile- butadiene-styrene (ABS) with nano-sized and micron-sized calcium carbonate. Polymer. 2005;46:243-52.

Kim K-H, Ong JL, Okuno O. The effect of filler loading and morphology on the mechanical properties of contemporary composites. The Journal of Prosthetic Dentistry. 2002;87:642-9.

International A. Standard test method for tensile properties of pultruded glass- fiber reinforced plastic rod.West Conshohocken (PA). ASTM 3916-12: ASTM International; 2002.

International A. Standard test method for flexural properties of fibre reinforced pultruded plastic rods. West Conshohocken (PA). ASTM D4475-96: ASTM International; 1997.

International A. Annual Book of ASTM Standard. Volume 08.01 plastics (I). West Conshohocken (PA). ASTM D256-D3159. ASTM International; 2005.

Vincent SR, Jaafar M, Palaniandy S. Properties of calcium carbonate/MICA and calcium farbonate/talc filled polypropylene composites. Journal of Engineering Science. 2014;10:41.

Borkar SP, Kumar VS, SS M. Effect of silica and calcium carbonate filler on the properties of woven fibre composites. India Journal of Fibre Textile Resource 2007;32:251-3

Tong JY, Royan NRR, Ng YC, Ab Ghani MH, Ahmad S. Study of the mechanical and morphology properties of recycled HDPE composite using rice husk filler. Advances in Materials Science and Engineering. 2014;2014.

Mitchell BS. An introduction to materials engineering and science for chemical and materials engineers: John Wiley & Sons; 2004.

Chen N, Wan C, Zhang Y, Zhang Y. Effect of nano-CaCO3 on mechanical properties of PVC and PVC/Blendex blend. Polymer Testing. 2004;23:169-74.

Hanna WA, Gharib FE, Marhoon II. Characterization of ceramic filled polymer matrix composite used for biomedical applications. Journal of Minerals and Materials Characterization and Engineering. 2011;10:1167.