Actuation and dynamic mechanical characteristics of a core free flat dielectric electro-active polymer soft actuator

Abdul Malek Abdul Wahab; Emiliano Rustighi; Zainudin A.

doi:10.15282/jmes.14.4.2020.08.0582

Authors

Abdul Malek Abdul Wahab Faculty of Mechanical Engineering Universiti Teknologi MARA, 40450 Shah Alam, Selangor, Malaysia. Phone: +60355436210; Fax: +60355435160
Emiliano Rustighi Institute of Sound and Vibration Research University of Southampton, U.K.
Zainudin A. Malaysia-Japan International Institute of Technology (MJIIT) Universiti Teknologi Malaysia Kuala Lumpur, Jalan Sultan Yahya Petra 54100 Kuala Lumpur, Malaysia

DOI:

https://doi.org/10.15282/jmes.14.4.2020.08.0582

Keywords:

dielectric electro-active polymer, soft actuator, actuation, dynamic, theoretical

Abstract

Various complex shapes of dielectric electro-active polymer (DEAP) actuator have been promoted for several types of applications. In this study, the actuation and mechanical dynamics characteristics of a new core free flat DEAP soft actuator were investigated. This actuator was developed by Danfoss PolyPower. DC voltage of up to 2000 V was supplied for identifying the actuation characteristics of the actuator and compare with the existing formula. The operational frequency of the actuator was determined by dynamic testing. Then, the soft actuator has been modelled as a uniform bar rigidly fixed at one end and attached to mass at another end. Results from the theoretical model were compared with the experimental results. It was found that the deformation of the current actuator was quadratic proportional to the voltage supplied. It was found that experimental results and theory were not in good agreement for low and high voltage with average percentage error are 104% and 20.7%, respectively. The resonance frequency of the actuator was near 14 Hz. Mass of load added, inhomogeneity and initial tension significantly affected the resonance frequency of the soft actuator. The experimental results were consistent with the theoretical model at zero load. However, due to inhomogeneity, the frequency response function’s plot underlines a poor prediction where the theoretical calculation was far from experimental results as values of load increasing with the average percentage error 15.7%. Hence, it shows the proposed analytical procedure not suitable to provide accurate natural frequency for the DEAP soft actuator.

References

R. Pelrine, R. Kornbluh, J. Joseph, R. Heydt, Q. Pei, and S. Chiba, “High-field deformation of elastomeric dielectrics for actuators,” Materials Science and Engineering: C, vol. 11, no. 2, pp. 89–100, Nov. 2000.

G. Kofod, “Dielectric elastomer actuators,” Smart Materials and Structures., vol. 14, no. September, pp. 1210–1216, 2001.

X. Yuan, S. Changgeng, G. Yan, and Z. Zhenghong, “Application review of dielectric electroactive polymers (DEAPs) and piezoelectric materials for vibration energy harvesting,” Journal of Physics: Conference Serie., vol. 744, no. 1, 2016.

B.-C. Yoseph and et al., “Electroactive polymer materials,” Smart Materials and Structures, vol. 16, no. 2, 2007.

Y. Bar-Cohen, “Electroactive Polymers as Artificial Muscles: Capabilities, Potentials and Challenges,” Robot. 2000, vol. c, pp. 188–196, 2000.

A. O’Halloran, F. O’Malley, and P. McHugh, “A review on dielectric elastomer actuators, technology, applications, and challenges,” Journal of Applied Physics, vol. 104, no. 7, 2008.

Z. Li, M. Sheng, M. Wang, P. Dong, B. Li, and H. Chen, “Stacked dielectric elastomer actuator (SDEA): Casting process, modeling and active vibration isolation,” Smart Materials and Structures, vol. 27, no. 7, p. 75023, Jul. 2018.

S. Hau, A. York, and S. Seelecke, “High-Force Dielectric Electroactive Polymer (DEAP) membrane actuator,” in SPIE, 2016, vol. 9798, p. 97980I.

U. Berardi, “Modelling and testing of a dielectic electro-active polymer (DEAP) actuator for active vibration control,” Journal of Mechanical Science and Technology, vol. 27, no. 1, pp. 1–7, Jan. 2013.

R. Sarban, R. W. Jones, B. R. Mace, and E. Rustighi, “A tubular dielectric elastomer actuator: Fabrication, characterization and active vibration isolation,” Mechanical Systems and Signal Processing, vol. 25, no. 8, pp. 2879–2891, 2011.

F. Carpi, G. Frediani, A. Mannini, and D. De Rossi, “Contractile and buckling actuators based on dielectric elastomers: Devices and applications,” CIMTEC 2008 - Proceeding of 3rd International Conference Smart Material Structure System - Artificial Muscle Actuators using Electroactive Polymer, vol. 61, pp. 186–191, 2008.

M. Benslimane, P. Gravesen, and P. Sommer-Larsen, “Mechanical properties of dielectric elastomer actuators with smart metallic compliant electrodes,” in Proceedings of SPIE, 2002, vol. 4695, pp. 150–157.

R. E. Pelrine, R. D. Kornbluh, and J. P. Joseph, “Electrostriction of polymer dielectrics with compliant electrodes as a means of actuation,” Sensors and Actuators A: Physical., vol. 64, no. 1, pp. 77–85, Jan. 1998.

Z. Suo, “Theory of dielectric elastomers,” Acta Mechanica Solida Sinica., vol. 23, no. 6, pp. 549–578, Dec. 2010.

K. Bertoldi and M. Gei, “Instabilities in multilayered soft dielectrics,” Journal of the Mechanics and Physics of Solids, vol. 59, no. 1, pp. 18–42, 2011.

L. Dong, M. Grissom, and F. T. Fisher, “Resonant frequency of mass-loaded membranes for vibration energy harvesting applications,” AIMS Energy, vol. 3, no. 3, pp. 344–359, 2015.

J. Maas, D. Tepel, and T. Hoffstadt, “Actuator design and automated manufacturing process for DEAP-based multilayer stack-actuators,” Meccanica, vol. 50, no. 11, pp. 2839–2854, Nov. 2015.