Relative assessment of various annular fin shapes for heat transfer and pressure penalty

Mayank Shah; Dr. Rupesh  Shah

doi:10.15282/jmes.16.4.2022.08.0732

Authors

M. Shah Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, 395007, Gujarat, India. Phone: 0261-2204785
R. Shah Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, 395007, Gujarat, India. Phone: 0261-2204785 https://orcid.org/0000-0002-7518-6415

DOI:

https://doi.org/10.15282/jmes.16.4.2022.08.0732

Keywords:

Turbulence, Heat trnafer, Forced convection, Potential rate

Abstract

Three dimensional numerical investigations are carried out to analyse the effect of different shapes of annular fin on heat transfer characteristics and pressure drop across a tube surface. Shear stress transport based k-ω turbulence model is used to analyse flow physics and heat transfer characteristics in flow domain. Weak zones of heat transfer across a circular tube surface are identified for 2500 < Re < 13000. Three different shapes of annular fin are considered to test the possibility of optimum heat transfer characteristics in weak zones. Results are compared with circular shape annular fin. Circular shape annular fin outperforms in terms of overall rate of heat transfer at the cost of highest pressure drop. The heat transfer rate decreases by 18%, 21% and 31% in sectorial fin, elliptical fin and sectional fin as compared to that of circular fin at 12965 Reynolds number, but at other end pressure drop across a tube surface in case of these fins also decrease as compared to that of circular annular fin. Potential rate, ratio of heat transfer rate to required pumping power, is calculated to evaluate optimum fin performance. Potential rate of an elliptical fin is highest among all the reported cases.

References

J. W. Scholten and D. B. Murray, “Unsteady heat transfer and velocity of a cylinder in cross flow—I. Low freestream turbulence,” International Journal of Heat and Mass Transfer, vol. 41, no. 10, pp. 1139–1148, 1998.

A. Ooi, L. Aye, K. Szczepanik, A. Ooi, L. Aye, and G. Rosengarten, “A numerical study of heat transfer from a cylinder in cross flow,” in 15th Australasian Fluid Mechanics Conference, Sydney, Australia, 2004.

L. Baranyi, S. Szabó, B. Bolló, and R. Bordás, “Analysis of low Reynolds number flow around a heated circular cylinder,” Journal of Mechanical Science and Technology, vol. 23, pp. 1829–1834, 2009.

C. C. Wang, W. S. Lee, and W. J. Sheu, “A comparative study of compact enhanced fin-and-tube heat exchangers,” International Journal of Heat and Mass Transfer, vol. 44, no. 18, pp. 3565–3573, Sep. 2001.

T. Perrotin and D. Clodic, “Fin efficiency calculation in enhanced fin and tube heat exchangers in dry condition,” International Congress of Refrigeration, vol. 18, 2003.

N. H. Kim and R. L. Webb, “Air-side heat transfer and friction correlations for plain fin-and-tube heat exchangers with staggered tube arrangements,” Journal of Heat Transfer, vol. 121, pp. 662–667, 1999.

M. Tutar and A. Akkoca, “Numerical analysis of fluid flow and heat transfer characteristics in three-dimensional plate fin-and-tube heat exchangers,” Numerical Heat Transfer, Part A: Applications, vol. 46, no. 3, pp. 301–321, Aug. 2004.

K. Park, D. H. Choi, and K. S. Lee, “Optimum design of plate heat exchanger with staggered pin arrays,” Numerical Heat Transfer, Part A: Applications, vol. 45, no. 4, pp. 347–361, 2004.

K. Torikoshi and G. Xi, “A numerical study of flow and thermal fields in finned tube heat exchangers (effect of the tube diameter),” in No. CONF-951135-. American Society of Mechanical Engineers, 1995.

S. Tang and K.-T. Yang, “Thermal performance of a single-row fin-and-tube heat exchanger,” Journal of Thermal Science, vol. 14, no. 2, pp. 172–180, 2005.

E. Gianolio and F. Cuti, “Heat transfer coefficients and pressure drops for air coolers with different numbers of rows under induced and forced draft,” Heat Transfer Engineering, vol. 3, no. 1, pp. 38–48, 1981.

Watel B, Harmand S, and Desmet B, “Influence of flow velocity and fin spacing on forced convective heat transfer from an annular finned tube,” JSME International Journal Series B Fluids and Thermal Engineering, vol. 42, no. 1, pp. 56–63, 1999.

M. S. Mon and U. Gross, “Numerical study of fin-spacing effects in annular-finned tube heat exchangers,” International Journal of Heat and Mass Transfer, vol. 47, no. 8–9, pp. 1953–1964, Apr. 2004.

T. W. H. Sheui, S. F. Tsai, and T. P. Chiang, “Numerical study of heat transfer in two-row heat exchangers having extended fin surfaces,” Numerical Heat Transfer, Part A: Applications, vol. 35, no. 7, pp. 797–814, May 1999.

H. Bilirgen, S. Dunbar, and E. K. Levy, “Numerical modeling of finned heat exchangers,” Applied Thermal Engineering, vol. 61, no. 2, pp. 278–288, Nov. 2013.

Taler D, “Experimental and numerical predictions of the heat transfer correlations in the cross-flow plate fin and tube heat exchangers,” Archives of Thermodynamics, vol. 28, no. 1, pp. 3–18, 2007.

H. T. Chen, J. C. Chou, and H. C. Wang, “Estimation of heat transfer coefficient on the vertical plate fin of finned-tube heat exchangers for various air speeds and fin spacings,” International Journal of Heat and Mass Transfer, vol. 50, no. 1–2, pp. 45–57, Jan. 2007.

G. Schüz and V. Kottke, “Visualization of flow, heat and mass transfer on finned tubes in cross flow,” in Flow Visualization IV, pp. 637–642, , 1987.

B. Kundu and P. K. Das, “Performance analysis and optimization of eccentric annular disk fins,” Journal of Heat Transfer, vol. 121, no. 1, pp. 128–135, Feb. 1999.

B. Kundu and P. K. Das, “Performance analysis and optimization of elliptic fins circumscribing a circular tube,” International Journal of Heat and Mass Transfer, vol. 50, no. 1–2, pp. 173–180, Jan. 2007.

A. H. Benmachiche, · F. Tahrour, · F. Aissaoui, · M. Aksas, and · C. Bougriou, “Comparison of thermal and hydraulic performances of eccentric and concentric annular-fins of heat exchanger tubes,” Heat and Mass Transfer, vol. 53, no. 8, pp. 2461–2471, 2001.

A. H. Benmachiche, C. Bougriou, F. Tahrour, and M. Aksas, “3-D numerical study and comparison of eccentric and concentric annular-finned tube heat exchangers Numerical simulation of forced convection heat transfer for annular finned tube heat exchangers.,” Journal of Engineering Science and Technology, vol. 10, no. 11, pp. 1508–1524, 2015.

M. Shah and R. Shah, “Numerical investigation to analyse the effect of fin shape on performance of finned tube heat exchanger,” Journal of Mechanical Engineering and Sciences, vol. 16, no. 3, pp. 9014–9024, Sep. 2022.

H. Nemati, A. R. Rahimzadeh, and C. chuan Wang, “Heat transfer simulation of annular elliptical fin-and-tube heat exchanger by transition SST model,” Journal of Central South University, vol. 27, no. 8, pp. 2324–2337, Aug. 2020.

R. K. Banerjee, M. Karve, J. H. Ha, D. H. Lee, and Y. I. Cho, “Evaluation of enhanced heat transfer within a four row finned tube array of an air cooled steam condenser,” Numerical Heat Transfer, Part A: Applications, vol. 61, no. 10, pp. 735–753, May 2012.

D. H. Lee, J. M. Jung, J. H. Ha, and Y. I. Cho, “Improvement of heat transfer with perforated circular holes in finned tubes of air-cooled heat exchanger,” International Communications in Heat and Mass Transfer, vol. 39, no. 2, pp. 161–166, Feb. 2012.

Y.A. Cengel, Heat and Mass Transfer-A practical approach, 2nd ed. 2003.