Numerical study of thermal and hydrodynamic characteristics of turbulent flow in hybrid corrugated channels with different wave profiles

Authors

DOI:

https://doi.org/10.15282/jmes.18.2.2024.5.0792

Keywords:

Hybrid groove profile, Heat transfer, Performance factor, Pressure drop, Turbulent flow

Abstract

The geometry of the wave profiles used in corrugated channels affects the flow and thermal characteristics. It is possible to increase thermal and hydraulic performance by simply changing the groove profile’s shape without using any additional energy. Therefore, this numerical study focused on the flow and thermal performance of different groove profiles in hybrid corrugated channels. The study was conducted using the finite volume method (FVM) with the standard k-ε turbulence model. The study consisted of three different hybrid corrugated channel flows created by combining the rectangular groove profile and the circular, trapezoidal, and triangular-shaped groove profiles separately. In addition, the numerical results were compared with the rectangular corrugated duct and the straight duct. The corrugated surfaces were kept constant at Tw = 380 K. Nusselt number, friction factor, and performance factor were calculated for different Reynolds numbers (2000 ≤ Re ≤ 10000). Images of flow and temperature contours were presented to demonstrate the effects of groove profiles. According to the numerical findings, the combination of the rectangular groove profile with other groove profiles significantly improved the heat transfer without any significant increase in pressure drop. The thermal performance was significantly affected by Re and the hybrid groove profiles. The rectangular-circular and rectangular-trapezoidal hybrid corrugated channels showed similar behaviors in terms of hydraulic and thermal attitude. It was determined that heat transfer in rectangular-circular and rectangular-trapezoidal hybrid groove profiles improved 4.38 times compared to straight ducts at Re = 8000 and 1.23 times compared to rectangular corrugated ducts at Re = 2000.

References

E. A. Handoyo, D. Ichsani, “Numerical studies on the effect of delta-shaped obstacles’ spacing on the heat transfer and pressure drop in V-corrugated channel of solar air heater,” Solar Energy, vol. 131, pp. 47-60, 2016.

H. Ameur, D. Sahel, “Effect of some parameters on the thermo-hydraulic characteristics of a channel heat exchanger with corrugated walls,” Journal of Mechanical and Energy Engineering, vol. 3, pp. 53-60, 2019.

A. Kaood, M. A. Hassan, “Thermo-hydraulic performance of nanofluids flow in various internally corrugated tubes,” Chemical Engineering and Processing-Process Intensification, vol. 154, p. 108043 2020.

R. K. Ajeel, W. I. Salim, K. Hasnan, “Experimental and numerical investigations of convection heat transfer in corrugated channels using alumina nanofluid under a turbulent flow regime,” Chemical Engineering Research and Design, vol. 148, pp. 202–217, 2019.

L. Matysiak and R. Platek, “Analytical, numerical, and experimental study of a robot controller with a forced cooling system,” Heat Transfer Research, vol. 50, no. 2, pp. 195-216, 2019.

M. Khan, S. Z. Shuja, B. S. Yilbas, and H. Al-Qahtani, “A case study on innovative design and assessment of a microchannel heat sink with various turbulators arrangements,” Case Studies in Thermal Engineering, vol. 31,

p. 101816, 2022.

I. Afaynou, H. Faraji, K. Choukairy, A. Arshad, M. Arıcı, “Heat transfer enhancement of phase-change materials (PCMs) based thermal management systems for electronic components: A review of recent advances,” International Communications in Heat and Mass Transfer, vol. 143, p. 106690, 2023.

J. M. Wua, J. Zhao, “A review of nanofluid heat transfer and critical heat flux enhancement research gap to engineering application,” Progress in Nuclear Energy, vol. 66, pp. 13-24, 2013.

T. Alam, M. H. Kim, “A comprehensive review on single phase heat transfer enhancement techniques in heat exchanger applications,” Renewable and Sustainable Energy Reviews, vol. 81, pp. 813-839, 2018.

J. Zhang, X. Zhu, M. E. Mondejar, F. Haglind, “A review of heat transfer enhancement techniques in plate heat exchangers,” Renewable and Sustainable Energy Reviews, vol. 101, pp. 305-328, 2019.

S. S. M. Ajarostaghi, M. Zaboli, H. Javadi, B. Badenes, J. F. Urchueguia, “A review of recent passive heat transfer enhancement methods,” Energies, vol. 15, p. 986, 2022.

S. Akcay, “Numerical analysis of heat transfer improvement for pulsating flow in a periodic corrugated channel with discrete V-type winglets,” International Communications in Heat Mass Transfer, vol. 134, p. 105991, 2022.

Z. Brodniansk´a, S. Kotˇsmíd, “Heat transfer enhancement in the novel wavy shaped heat exchanger channel with cylindrical vortex generators,” Applied Thermal Engineering, vol. 220, p. 119720, 2023.

S. Akcay, U. Akdag, “Heat transfer enhancement in a channel with inclined baffles under pulsating flow: A CFD study,” Journal of Enhanced Heat Transfer, vol. 30, no. 5, pp. 61-79, 2023.

W. He, D. Toghraie, A. Lotfipour, F. Pourfattah, A. Karimipour, M. Afrand, “Effect of twisted-tape inserts and nanofluid on flow field and heat transfer characteristics in a tube,” International Communications in Heat and Mass Transfer, vol. 110, p. 104440, 2020.

R. H. Monfared, M. Niknejadi, D. Toghraie, P. Barnoon, “Numerical investigation of swirling flow and heat transfer of a nanofluid in a tube with helical ribs using a two-phase model,” Journal of Thermal Analysis and Calorimetry, vol. 147, no. 4, pp. 3403–3416, 2022.

C-N. Feng, C-H. Liang, Z-X. Li, “Friction factor and heat transfer evaluation of cross-corrugated triangular flow channels with trapezoidal baffles,” Energy & Buildings, vol. 257, p. 111816, 2022.

L. K. Nitturi, V. K. S. Kapu, R. Gugulothu, A. Kaleru, V. Vuyyuri, A. Farid, “Augmentation of heat transfer through passive techniques,” Heat Transfer, vol. 52, no. 6, pp. 4422-4449, 2023.

N. Kurtulmus, B. Sahin, “A review of hydrodynamics and heat transfer through corrugated channels,” International Communications in Heat and Mass Transfer, vol. 108, p. 104307, 2019.

D. Haridas, V. Singh, A. Srivastava, “An experimental investigation of heat transfer performance of wavy channels under laminar flow conditions: An interferometric study,” Journal of Enhanced Heat Transfer, vol. 27, no. 6, pp. 561-576, 2020.

K. Kumar, R. Kumar, R. S. Bharj, P. K. Mondal, “Irreversibility analysis of the convective flow through corrugated channels: A comprehensive review,” The European Physical Journal Plus, vol. 136, no. 4, pp. 1–40, 2021.

M. A. Alfellag, H. E. Ahmed, M. G. Jehad, A. A. Farhan, “The hydrothermal performance enhancement techniques of corrugated channels: A review,” Journal of Thermal Analysis and Calorimetry, vol. 147, pp. 10177-10206, 2022.

M. Esmaeili, K. Sadeghy, M. Moghaddami, “Heat transfer enhancement of wavy channels using Al2O3 nanoparticles,” Journal of Enhanced Heat Transfer, vol. 17, no. 2, pp. 139-151, 2010.

P. M. Mithun Krishna, M. Deepu, S. R. Shine, “Numerical investigation of wavy microchannels with rectangular cross section,” Journal of Enhanced Heat Transfer, vol. 25, no. 4-5, pp. 293-313, 2018.

B. Saleh, L.S. Sundar, “Experimental study on heat transfer, friction factor, entropy and exergy efficiency analyses of a corrugated plate heat exchanger using Ni/water nanofluids,” International Journal of Thermal Sciences, vol. 165, p. 106935, 2021.

W. Wang, Y. Zhang, J. Liu, B. Li, B. Sund´en, “Numerical investigation of entropy generation of turbulent flow in a novel outward corrugated tube,” Journal of Heat and Mass Transfer, vol. 126, pp. 836–847, 2018.

R. K. Ajeel, W. Saiful-Islam, K. Sopian, M. Z. Yusoff, “Analysis of thermal-hydraulic performance and flow structures of nanofluids across various corrugated channels: An experimental and numerical study,” Thermal Science and Engineering Progress, vol. 19, p. 10060, 2020.

F. Ahmad, S. Mahmud, M. M. Ehsan, M. Salehin, “Numerical assessment of nanofluids in corrugated minichannels: Flow phenomenon and advanced thermo-hydrodynamic analysis,” International Journal of Thermofluids, vol. 20, p. 100449, 2023.

M. Khoshvaght-Aliabadi, “Influence of different design parameters and Al2O3-water nanofluid flow on heat transfer and flow characteristics of sinusoidal-corrugated channels,” Energy Conversion and Management, vol. 88, pp. 96–105, 2014.

M. E. Nakhchi, “Experimental optimization of geometrical parameters on heat transfer and pressure drop inside sinusoidal wavy channels,” Thermal Science and Engineering Progress, vol. 9, pp. 121–131, 2019.

R. K. Ajeel, W. I. Salim, K. Hasnan, “Design characteristics of symmetrical semicircle- corrugated channel on heat transfer enhancement with nanofluid,” International Journal of Mechanical Sciences, vol. 151, pp. 236–250, 2019.

H. Togun, R. Z. Homod, Z. M. Yaseen, A. M. Abed, J. M. Dhabab, R. K. Ibrahem, et al., “Efficient heat transfer augmentation in channels with semicircle ribs and hybrid Al2O3-Cu/water nanofluids,” Nanomaterials, vol. 12, no. 15, p. 2720, 2022.

S. Akcay, “Heat transfer analysis of pulsating nanofluid flow in a semicircular wavy channel with baffles,” Sādhanā, vol. 48, no. 57, 2023.

L. Z. Zhang, “Numerical study of periodically fully developed flow and heat transfer in cross-corrugated triangular channels in transitional flow regime,” Numerical Heat Transfer, Part A: Applications, vol. 48, no. 4, pp. 387–405, 2005.

S. K. Mehta, S. Pati, “Analysis of thermo-hydraulic performance and entropy generation characteristics for laminar flow through triangular corrugated channel,” Journal of Thermal Analysis Calorimetry, vol. 136, 1, pp. 49–62, 2019.

E. N. Krishnan, H. Ramin, A. Guruabalan, C. J. Simonson, “Experimental investigation on thermo-hydraulic performance of triangular cross-corrugated flow passages,” International Communications in Heat and Mass Transfer, vol. 122, p. 105160, 2021.

Z-X. Li, S-Q. Sung, C. Wang, C-H. Liang, S. Zeng, T. Zhong, et al., “The effect of trapezoidal baffles on heat and flow characteristics of a cross-corrugated triangular duct,” Case Studies in Thermal Engineering, vol. 33, p. 101903, 2022.

A. M. Abed, M. A. Alghoul, K. Sopian, H. A. Mohammed, A. N. Al-Shamani, “Design characteristics of corrugated trapezoidal plate heat exchangers using nanofluids,” Chemical Engineering Processing: Process Intensification, vol. 87 pp. 88–103, 2015.

R. K. Ajeel, W. I. Salim, K. Hasnan, “Influences of geometrical parameters on the heat transfer characteristics through symmetry trapezoidal-corrugated channel using SiO2-water nanofluid,” International Communications Heat Mass Transfer, vol. 101, pp. 1–9, 2019.

H. Zontul, H. Hamzah, N. Kurtulmuş, B. Şahin, “Investigation of convective heat transfer and flow hydrodynamics in rectangular grooved channels,” International Communications in Heat and Mass Transfer, vol. 126, p. 105366, 2021.

R. K. Ajeel, R. Zulkifli, K. Sopian, S. N. Fayyadh, A. Fazlizan, A. Ibrahim, “Numerical investigation of binary hybrid nanofluid in new configurations for curved- corrugated channel by thermal-hydraulic performance method,” Powder Technology, vol. 385, pp. 144–159, 2021.

Y. Zheng, H. Yang, H. Mazaheri, A. Aghaei, N. Mokhtari, M. Afrand, “An investigation on the influence of the shape of the vortex generator on fluid flow and turbulent heat transfer of hybrid nanofluid in a channel,” Journal of Thermal Analysis and Calorimetry, vol. 143, pp. 1425–1438, 2021.

M. Khan, I. N. Alsaduni, M. Alluhaidan, W-F. Xia, M. Ibrahim, “Evaluating the energy efficiency of a parabolic trough solar collector filled with a hybrid nanofluid by utilizing double fluid system and a novel corrugated absorber tube,” Journal of the Taiwan Institute of Chemical Engineers, vol. 124, pp. 150-161, 2021.

H. A. Mohammed, A. M. Abed, M. A. Wahid, “The effects of geometrical parameters of a corrugated channel with in out-of-phase arrangement,” International Communications in Heat and Mass Transfer, vol. 40, pp. 47-57, 2013.

M. K. Aktas, O. Baser, S. R. Angeneh, “Effects of pulsating flow on convection in wavy channels with phase shift,” Heat Transfer Research, vol. 51, no. 9, pp. 865-878, 2020.

R. K. Ajeel, W. S-I. W. Salim, K. Hasnan, “Thermal and hydraulic characteristics of turbulent nanofluids flow in trapezoidal-corrugated channel: Symmetry and zigzag shaped,” Case Studies in Thermal Engineering, vol. 12, pp. 620–635, 2018.

R. K. Ajeel, W. I. Salim, K. Sopian, M. Z. Yusoff, K. Hasnan, A. Ibrahim, et al., “Turbulent convective heat transfer of silica oxide nanofluid through corrugated channels: an experimental and numerical study,” International Journal of Heat Mass Transfer, vol. 145, p. 118806, 2019.

T. Choudhary, M. K. Sahu, V. Shende, A. Kumar, “Computational analysis of a heat transfer characteristic of a wavy and corrugated channel,” Material Today: Proceedings, vol. 56, pp. 263-273, 2022.

A. Naderifar, M. Nikian, K. Javaherdeh, M. Borji, “Numerical investigation of the effect of fins on heat transfer enhancement of a laminar non-newtonian nanofluid flow through a corrugated channel,” Journal of Thermal Analysis and Calorimetry, vol. 147, pp. 9779-9791, 2022.

L. Zhang, D. Che, “Influence of corrugation profile on the thermal hydraulic performance of cross-corrugated plates,” Numerical Heat Transfer, Part A: Applications, vol. 59, no. 4, pp. 267–296, 2011.

M. Ahmed, M. Yusoff, K. Ng, N. Shuaib, “Effect of corrugation profile on the thermal–hydraulic performance of corrugated channels using CuO–water nanofluid,” Case Studies in Thermal Engineering, vol. 4, pp. 65-75, 2014.

M. Salami, M. Khoshvaght-Aliabadi, A. Feizabadi, “Investigation of corrugated channel performance with different wave shapes,” Journal of Thermal Analysis and Calorimetry, vol. 138, no. 5, pp. 3159–3174, 2019.

R. K. Ajeel, W. S-I. W. Salim, K. Hasnan, “Thermal performance comparison of various corrugated channels using nanofluid: Numerical study,” Alexandria Engineering Journal, vol. 58, pp. 75–87, 2019b.

S. S. Shahsavar, I. B. Alimohammadi, Askari, H. M. Ali, “Numerical investigation of the effect of corrugation profile on the hydrothermal characteristics and entropy generation behavior of laminar forced convection of non-Newtonian water/CMC-CuO nanofluid flow inside a wavy channel,” International Communication in Heat and Mass Transfer, vol. 121, p. 105117, 2021.

R. K. Ajeel, K. Sopian, R. Zulkifli, “A novel curved-corrugated channel model: thermal-hydraulic performance and design parameters with nanofluid,” International Communications in Heat Mass Transfer, vol. 120, p. 105037, 2021.

K. Kumar, R. Kumar, R. S. Bharl, “Thermohydraulic performance enhancement using novel hybrid corrugation configuration channels in thermal systems,” International Communications in Heat and Mass Transfer, vol. 134, p. 105999, 2022.

ANSYS Inc., ANSYS Fluent User Guide & Theory Guide- Release 15.0, USA, 2015.

S. Akcay, “Numerical study of turbulent heat transfer process in different wavy channels with solid and perforated baffles,” Heat Transfer Research, vol 54, no. 18, pp. 53-82, 2023.

Y. A. Cengel, J. M. Cimbala. Fluid Mechanics, 3rd Ed. New York: Tata McGraw-Hill Education, 2010.

Downloads

Published

2024-06-28

How to Cite

[1]
D. Uysal and S. . Akçay, “Numerical study of thermal and hydrodynamic characteristics of turbulent flow in hybrid corrugated channels with different wave profiles”, J. Mech. Eng. Sci., vol. 18, no. 2, pp. 10026–10045, Jun. 2024.

Issue

Section

Article

Similar Articles

You may also start an advanced similarity search for this article.