Effect of conical pin arrangement on heat transfer efficiency of a free convective solar air heater

S.E. Gilani; H.H. Al-Kayiem; D.E. Woldemicheal

doi:10.15282/jmes.10.2.2016.10.0194

Authors

S.E. Gilani Department of Mechanical Engineering, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Perak, Malaysia
H.H. Al-Kayiem Department of Mechanical Engineering, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Perak, Malaysia
D.E. Woldemicheal Department of Mechanical Engineering, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Perak, Malaysia

DOI:

https://doi.org/10.15282/jmes.10.2.2016.10.0194

Keywords:

Artificial roughness; solar air heater; enhanced heat transfer; pin shape turbulators

Abstract

The artificial roughnesses on absorber plate have been known to enhance the performance of the solar air heater under forced convection. The objective of this paper is to study the effect of conical pin arrangement on the heat transfer enhancement of free convective solar air heater. The conical pins were arranged in-line and in staggered arrangement with the pitch-to-height ratio of eight. The height of the conical pin was fixed at 0.2 cm. The measurement results revealed that the use of conical pin on the surface of absorber plate helped to improve the overall efficiency of the solar air heater. The staggered arrangement of the conical pins performed better compared to the case of the in-line arrangement. The performance of the solar air heater with the staggered arrangement was 42% higher than that of the flat absorber plate with no pins at 435 W/m2 while the in-line arrangement showed an increase of 28%. Hence, the use of the artificial pin roughening technique with the staggered arrangement is recommended in the free convection solar air heater.

References

Shafiee S, Topal E. When will fossil fuel reserves be diminished? Energy Policy. 2009;37:181-9.

Kalogirou SA. Solar thermal collectors and applications. Progress in energy and combustion science. 2004;30:231-95.

Sulaiman SA, Murad SHM, Abdul Karim ZA. Study of flow in air-intake system for a single-cylinder go-kart engine. International Journal of Automotive and Mechanical Engineering (IJAME). 2010;1:91-104.

Kumar S, Sinha S, Kumar N. Experimental investigation of solar chimney assisted bioclimatic architecture. Energy Conversion and Management. 1998;39:441-4.

Zhai XQ, Dai YJ, Wang RZ. Experimental investigation on air heating and natural ventilation of a solar air collector. Energy and Buildings. 2005;37:373-81.

Verma R, Chandra R, Garg HP. Parametric studies on the corrugated solar air heaters with and without cover. Renewable Energy. 1991; 1(3): 361-71.

Azad AK, Rasul MG, Mofijur M, Bhuiya MMK, Mondal SK, Sattar MK. Energy and Waste Management for Petroleum Refining Effluents: A Case Study in Bangladesh. International Journal of Automotive and Mechanical Engineering. 2015;11:2170-87.

Omer AM. Built environment: Relating the benefits of renewable energy technologies. International Journal of Automotive and Mechanical Engineering. 2012;5:561-75.

Duffie JA, Beckman WA. Solar Engineering of Thermal Processes: Fourth Edition. New Jersey: John Wiley and Sons; 2013.

Hwang SD, Kwon HG, Cho HH. Heat transfer with dimple/protrusion arrays in a rectangular duct with a low Reynolds number range. International journal of heat and fluid flow. 2008;29:916-26.

Yadav S, Kaushal M. Nusselt number and friction factor correlations for solar air heater duct having protrusions as roughness elements on absorber plate. Experimental Thermal and Fluid Science. 2013;44:34-41.

Mahendran M, Lee GC, Shahrani A, Bakar RA, Kadirgama K. Diurnal Pattern and Estimation of Global Solar Radiation in East Coast Malaysia. International Journal of Automotive and Mechanical Engineering. 2013;8:1162-75.

Al-Kayiem HH, Md Yunus Y. Drying of Empty Fruit Bunches as Wasted Biomass by Hybrid Solar–Thermal Drying Technique. Journal of Mechanical Engineering and Sciences. 2013;5:652-61.

Mahendran M, Lee GC, Sharma KV, Shahrani A. Performance of evacuated tube solar collector using water-based titanium oxide nanofluid. Journal of Mechanical Engineering and Sciences. 2012;3:301-10.

Saurav S, Bartaria VN. Heat transfer and thermal efficiency of solar air heater having artificial roughness: a review. International Journal of Renewable Energy Research (IJRER). 2013;3:498-508.

Obot NT, Esen EB, Rabas TJ. The role of transition in determining friction and heat transfer in smooth and rough passages. International Journal of Heat and Mass Transfer. 1990;33:2133-43.

Karwa R, Solanki SC, Saini JS. Heat transfer coefficient and friction factor correlations for the transitional flow regime in rib-roughened rectangular ducts. International Journal of Heat and Mass Transfer. 1999;42:1597-615.

Bhagoria JL, Saini JS, Solanki SC. Heat transfer coefficient and friction factor correlations for rectangular solar air heater duct having transverse wedge shaped rib roughness on the absorber plate. Renewable Energy. 2002;25:341-69.

Jaurker AR, Saini JS, Gandhi BK. Heat transfer and friction characteristics of rectangular solar air heater duct using rib-grooved artificial roughness. Solar Energy. 2006;80:895-907.

Layek A, Saini JS, Solanki SC. Effect of chamfering on heat transfer and friction characteristics of solar air heater having absorber plate roughened with compound turbulators. Renewable Energy. 2009;34:1292-8.

Kumar A, Bhagoria JL, Sarviya RM. Heat transfer and friction correlations for artificially roughened solar air heater duct with discrete W-shaped ribs. Energy Conversion and Management. 2009;50:2106-17.

Saini RP, Saini JS. Heat transfer and friction factor correlations for artificially roughened ducts with expanded metal mesh as roughness element. International Journal of Heat and Mass Transfer. 1997;40:973-86.

Xie G, Sundén B, Zhang W. Comparisons of pins/dimples/protrusions cooling concepts for a turbine blade tip-wall at high Reynolds numbers. Journal of Heat Transfer. 2011;133:061902.

Al-Kayiem HH, Mahdi HAA. Performance enhancement of rotary air preheater by the use of pin shaped turbulators. Advanced Computational Methods and Experiments in Heat Transfer XI. 2010;68:35-49.

Yeh HM, Lin TT. The effect of collector aspect ratio on the collector efficiency of flat-plate solar air heaters. Energy. 1995;20:1041-7.

Chen W, Qu M. Analysis of the heat transfer and airflow in solar chimney drying system with porous absorber. Renewable Energy. 2014;63:511-8.

Majid ZAA, Razak AA, Ruslan MH, Sopian K. Characteristics of solar thermal absorber materials for cross absorber design in solar air collector. International Journal of Automotive and Mechanical Engineering. 2015;11:2582-90.

Mathur J, Mathur S, Anupma. Summer-performance of inclined roof solar chimney for natural ventilation. Energy and Buildings. 2006;38:1156-63.

Al-Kayiem HH, Yassen TA. On the natural convection heat transfer in a rectangular passage solar air heater. Solar Energy. 2015;112:310-8.

Bansal NK, Garg HP. An experimental study on a finned type and non-porous type solar air heater with a solar simulator. Energy conversion and management. 1985;25:135-8.

Pangavhane DR, Sawhney RL, Sarsavadia PN. Design, development and performance testing of a new natural convection solar dryer. Energy. 2002;27:579-90.

Bou-Rabee MA, Sulaiman SA, Choe G, Han D, Saeed T, Marafie S. Characteristics of solar energy radiation on typical summer and winter days in Kuwait. International Journal of Automotive and Mechanical Engineering. 2015;12:2944-53.

Dey M, Dandotiya DS. A Critical Analysis on investigation methods Used in Artificially Roughened Solar Air Heaters system:(A Review). International Journal of Emerging Trends in Engineering and Development. 2013;4:306-19.

Zhang LW, Balachandar S, Tafti DK, Najjar FM. Heat transfer enhancement mechanisms in inline and staggered parallel-plate fin heat exchangers. International Journal of Heat and Mass Transfer. 1997;40:2307-25.