Investigation on changes in gamma prime precipitate on varying surface locations of IN738 engine turbine blade

M.S. Hamizol; P.S.M. Megat-Yusof; M.A. Nasrudin; M.A. Meor Said; M.S. Jasmani; S.M.A. Syed Ahmad Ghazali

doi:10.15282/jmes.10.2.2016.12.0196

Authors

M.S. Hamizol Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
P.S.M. Megat-Yusof Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
M.A. Nasrudin Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
M.A. Meor Said Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
M.S. Jasmani PETRONAS Upstream, Level 48, PETRONAS Tower 3, Kuala Lumpur City Centre 50088 Kuala Lumpur, Malaysia
S.M.A. Syed Ahmad Ghazali PETRONAS Carigali Sdn. Bhd., Peninsular Malaysia Operations, Kompleks Operasi Petronas, 24300 Kertih, Kemaman, Terengganu, Malaysia

DOI:

https://doi.org/10.15282/jmes.10.2.2016.12.0196

Keywords:

Microstructure; gamma prime precipitate; equilibrium phase; SEM; EDX

Abstract

Changes in microstructure of a service exposed turbine engine blade have been found to affect the elemental composition and the performance because the existing bond structures, as well as the phase distribution of the blade material, deteriorates as a consequence of the changes. As such, this systematic internal deformation, which can expedite the creep and crack formation, has been a source of concern for the industry. Besides, failure in understanding these microstructural changes can lead to disregard of necessary and vital preventive measures. Hence, the present study investigates a turbine engine blade with estimated operating hours of 52000 at ±720oC to examine the changes that occur in the microstructure of blade material from different points of the blade. For that purpose, scanning electron microscopy (SEM) was used to analyse the grain boundary formation and the gamma prime precipitates. In fact, the presence of the gamma prime phase in the microstructure had been proven to be a major contributing factor that enhanced nucleation and propagation creep. Other than that, the varied locations on the blade were examined and compared to determine the critical points that affected the performance of blade during operation using an electric discharge machine (EDM). Furthermore, the development of gamma prime precipitates had been rather obvious in the equilibrium phase than that in the solid phase due to temperature variation. On top of that, the transformation in the pressure surface location displayed more intensity than the suction surface location, in which limited carbides (MC) was observed in the suction surface location, whereas the grain boundary growth had been sporadic. However, continuous gamma prime precipitate was discovered in the pressure surface location. Hence, this study infers that changes that take place in the microstructure of the blade do not solely depend on the hours exposed or the intensity of subjected pressure, but such changes are deemed to occur due to a number of other essential aspects, for instance, material bulk properties, alloy constituents, loss of surface coherence, coarsening, and condition of operation.

References

Reddy LR. Creep life estimation of gas turbine blade. 2016.

Epishin A, Link T, Klingelhöffer H, Fedelich B, Portella P. Creep damage of single-crystal nickel base superalloys: mechanisms and effect on low cycle fatigue. Materials at high temperatures. 2014.

Dewangan R, Patel J, Dubey J, Sen PK, Bohidar SK. Gas turbines blades-a critical review of failure on first and second stages. International Journal of Mechanical Engineering and Robotics Research. 2015;4:216.

Kovacs S, Beck T, Singheiser L. Influence of mean stresses on fatigue life and damage of a turbine blade steel in the VHCF-regime. International Journal of Fatigue. 2013;49:90-9.

Caron P. High y'solvus new generation nickel-based superalloys for single crystal turbine blade applications. Superalloys 2000. 2000:737-46.

Sajjadi SA, Zebarjad SM, Guthrie R, Isac M. Microstructure evolution of high- performance Ni-base superalloy GTD-111 with heat treatment parameters. Journal of materials processing technology. 2006;175:376-81.

Donachie MJ, Donachie SJ. Superalloys: a technical guide: ASM international; 2002.

Wilson JM, Piya C, Shin YC, Zhao F, Ramani K. Remanufacturing of turbine blades by laser direct deposition with its energy and environmental impact analysis. Journal of Cleaner Production. 2014;80:170-8.

Sujata M, Madan M, Raghavendra K, Venkataswamy M, Bhaumik S. Microstructural study: an aid to determination of failure mechanism in nickel base superalloy blades. Transactions of the Indian Institute of Metals. 2010;63:681-5.

Lvova E, Norsworthy D. Influence of service-induced microstructural changes on the aging kinetics of rejuvenated Ni-based superalloy gas turbine blades. Journal of materials engineering and performance. 2001;10:299-312.

Rybnikov A, Getsov L, Leontiev S. Failure analysis of gas turbine blades. Microscopy and Microanalysis. 2005;11:222-3.

Mikami M, Sawada K, Kobayashi S, Hara T, Kimura K. Microstructural change after long-term creep exposure in high cr steel forgings for ultrasupercritical steam turbine rotors. Advances in Materials Technology for Fossil Power Plants: Proceedings from the Seventh International Conference, October 22-25, 2013 Waikoloa, Hawaii, USA: ASM International; 2014. p. 293.

Tong J, Ding X, Wang M, Yagi K, Zheng Y, Feng Q. Assessment of service induced degradation of microstructure and properties in turbine blades made of GH4037 alloy. Journal of Alloys and Compounds. 2016;657:777-86.

Kuhn F, Zeismann F, Brückner-Foit A, Kadau K, Gravett P. Crack paths in the superalloy IN738 in aged conditions. Engineering Fracture Mechanics. 2013;108:275-84.

Murr L, Martinez E, Pan X, Gaytan S, Castro J, Terrazas C, et al. Microstructures of Rene 142 nickel-based superalloy fabricated by electron beam melting. Acta Materialia. 2013;61:4289-96.