EFFECT OF GEAR RATIO ON THE DC MOTOR EFFICIENCY OF A MINIFUEL-CELL VEHICLE CRUISING AT CONSTANT SPEEDS
DOI:
https://doi.org/10.15282/jmes.8.2015.20.0142Keywords:
Traction Motor; Efficiency; Gear Ratio; PEM Fuel-Cell Vehicle, Constant SpeedAbstract
The traction motor is a key component in a fuel-cell vehicle as it converts electrical energy supplied by a fuel cell into mechanical shaft work for vehicle propulsion. Motor size, torque rating and current consumption are important factors in the selection of the optimum drive motor for best energy efficiency. In a practical power train assembly, the motor is coupled to the wheel via a gearing system. This study focuses on the performance with respect to traction motor efficiency relative to the gear ratio selection and variable drive cycles to minimize the power consumption of the vehicle. A test bench with a 1 kW fuel cell was developed and tests were performed at constant speeds between 15 km/h to 30 km/h with different gear ratios. Among the measured and evaluated parameters using Eagle Tree and Inertia data loggers are rpm, current, torque and power. The results show that the gear ratio selection produces a variation in required motor input power at similar drive speeds. It also shows the optimal setting of the gear ratio of more than 70% that suits the best efficiency point of the DC motor according to actual driving requirements.
References
Hwang JJ, Chen YJ, Kuo JK. The study on the power management system in a fuel cell hybrid vehicle. International Journal of Hydrogen Energy. 2012;37:4476-89.
Pollet BG, Staffell I, Shang JL. Current status of hybrid, battery and fuel cell electric vehicles: from electrochemistry to market prospects. Electrochim Acta. 2012;84:235-49.
Van Vliet OP, Kruithof T, Turkenburg WC, Faaij AP. Techno-economic comparison of series hybrid, plug-in hybrid, fuel cell and regular cars. Journal of Power Sources. 2010;195:6570-85.
Ghobadian B, Najafi G, Nayebi M. A semi-empirical model to predict diesel engine combustion parameters. Journal of Mechanical Engineering and Sciences. 2013;4:373-82.
Kalyani Radha K, Naga Sarada S, Rajagopal K, Nagesh EL. Performance and emission characteristics of CI engine operated on vegetable oils as alternative fuels. International Journal of Automotive and Mechanical Engineering. 2011;4:414-27.
Mohamed WANW, Atan R. Polymer electrolyte membrane fuel cell. International Journal of Automotive and Mechanical Engineering. 2012;5:648-59.
Kamil M, Rahman MM, Bakar RA. Integrated simulation model for composition and properties of gases in hydrogen fueled engine. International Journal of Automotive and Mechanical Engineering. 2013;8:1242-155.
Azad A, Ameer Uddin S, Alam M. A Comprehensive Study of Di Diesel Engine Performance With Vegetable Oil: An Alternative Bio-Fuel Source of Energy. International Journal of Automotive and Mechanical Engineering. 2012;5:576-86.
Kamil M, Rahman MM, Bakar RA. Performance evaluation of external mixture formation strategy in hydrogen fueled engine. Journal of Mechanical Engineering and Sciences. 2011;1:87-98.
Rahim R, Mamat R, Taib MY, Abdullah AA. Influence of fuel temperature on a diesel engine performance operating with biodiesel blended. Journal of Mechanical Engineering and Sciences. 2012;2:226-36.
Ho T, Karri V, Lim D, Barret D. An investigation of engine performance parameters and artificial intelligent emission prediction of hydrogen powered car. International Journal of Hydrogen Energy. 2008;33:3837-46.
Ho T, Karri V. Basic tuning of hydrogen powered car and artificial intelligent prediction of hydrogen engine characteristics. International Journal of Hydrogen Energy. 2010;35:10004-12.
Kapilan N, Ashok Babu TP, Reddy RP. Improvement of performance of dual fuel engine operated at part load. International Journal of Automotive and Mechanical Engineering. 2010;2:200-10.
Nematizade P, Ghobadian B, Najafi G. Investigation of fossil fuels and liquid biofuels blend properties using artificial neural network. International Journal of Automotive and Mechanical Engineering. 2012;5:639-47.
Tirnovan R, Giurgea S. Efficiency improvement of a PEMFC power source by optimization of the air management. International Journal of Hydrogen Energy. 2012;37:7745-56.
Corbo P, Migliardini F, Veneri O. Performance investigation of 2.4 kW PEM fuel cell stack in vehicles. International Journal of Hydrogen Energy. 2007;32:4340-9.
Akyalçın L, Kaytakoğlu S. Optimization of structural combinations on the performance of a PEMFC's MEA. Journal of Power Sources. 2008;180:767-72.
Abdullah NR, Shahruddin NS, Mamat R, Ihsan Mamat AM, Zulkifli A. Effects of air intake pressure on the engine performance, fuel economy and exhaust emissions of a small gasoline engine. Journal of Mechanical Engineering and Sciences. 2014;6:949-58.
Hairuddin AA, Wandel AP, Yusaf T. An Introduction to a Homogeneous Charge Compression Ignition Engine. Journal of Mechanical Engineering and Sciences. 2014;7:1042-52.
Chan C. Overview of Electric Vehicles-Clean and Energy Efficient Urban Transportation. PEMC’96. Budapest, Hungary1996. p. 7-15.
Larminie J, Lowry J. Electric vehicle technology explained: John Wiley & Sons; 2004.
Karatzaferis JC, Lampropoulos LS, Tatakis EC. Efficiency improvement in DC and AC motor powered electric vehicles. Proceedings of the 2011-14th European Conference on Power Electronics and Applications (EPE 2011): IEEE; 2011. p. 1-10.
Chau K, Chan C, Liu C. Overview of permanent-magnet brushless drives for electric and hybrid electric vehicles. IEEE Transactions on Industrial Electronics. 2008;55:2246-57.
Kamachi M, Miyamoto H, Sano Y. Development of power management system for electric vehicle “i-MiEV”. International Power Electronics Conference IEEE; 2010. p. 2949-55.
