Vol. 13 No. 1 (2019): (March 2019)

Article

• Mechanical characterization and optimization of heat treatment parameters of manganese alloyed austempered ductile iron

  Ananda Hegde, Sathyashankara Sharma, Ramakrishna Vikas Sadanand

  4356-4367

  • PDF

• Influence of fins designs, geometries and conditions on the performance of a plate-fin heat exchanger-experimental perspective

  M. I. N. Ma’arof, Girma T. Chala, Hazran Husain, Muhammad S. S. Mohamed

  4368-4379

  • PDF

• Mechanical characterization of heat treated Al2219 hybrid composites

  Gowrishankar M. C., Sathyashankara Sharma, B. K. Pavan, Kamath Kiran, Kumar Rajendra, Pavan Hiremath, Manjunath Shettar

  4380-4389

  • PDF

• Fuel as secondary refrigerant on LPG fuelled vehicle: A thermodynamics analysis

  Muji Setiyo, B. Waluyo

  4390-4402

  • PDF

• Effects of heat energy on morphology and properties of selective inhibition sintered high density polyethylene

  D. Rajamani, E Balasubramanian

  4403-4414

  • PDF

• Evaluation of induced residual stresses on AISI 1020 low carbon steel plate from experimental and FEM approach during TIG welding process

  I. B. Owunna, A. E. Ikpe

  4415-4433

  • PDF

• Gravimetric, electrochemical and surface study on the good’s buffer ionic liquid as corrosion inhibitor for carbon steel in acidic medium

  R. Nanthini, M. I. Mutalib, K. A. Kurnia

  4434-4448

  • PDF

• Fracture cause analysis of the extruder’s shaft and geometry optimization of the spline

  O. Lyashuk, Y. Pyndus, I. Lutsiv, Y. Vovk, L. Poberezhna, O. Tretiakov, R. Zolotyy

  4449-4460

  • PDF

• Analysis of wind energy potential and wind energy development to evaluate performance of wind turbine installation in Bali, Indonesia

  Nyoman Ade Satwika, R. Hantoro, E. Septyaningrum, A. W. Mahmashani

  4461-4476

  • PDF

• Iterative variational mode decomposition and extreme learning machine for gearbox diagnosis based on vibration signals

  M. Firdaus Isham, M. Salman Leong, L. M. Hee, Z. A. B. Ahmad

  4477-4492

  • PDF

• Characterisation of heterogeneities and evaluation of properties of nuclear grade graphite

  S. Negi, J. Korody, I. Khan, D. Kanse

  4493-4502

  • PDF

• Drag reduction by combination of flow control using inlet disturbance body and plasma actuator on cylinder model

  Budiarso ., Harinaldi ., E. A. Kosasih, R. F. Karim, J. Julian

  4503-4511

  • PDF

• Simulation and experimental response of four-bar mechanism with tolerance stack

  Chandrashekhar A. Akhadkar, Ashish B. Deoghare, Adwait M. Vaidya

  4512-4535

  • PDF

• Application of low transformation-temperature filler to reduce the residual stresses in welded component

  K. Azizpour, H. Moshayedi, I. Sattari-far

  4536-4557

  • PDF

• Heat transfer characteristics on MHD Powell-Eyring fluid flow across a shrinking wedge with non-uniform heat source/sink

  K. Anantha Kumar, B. Ramadevi, V. Sugunamma, J. V. Ramana Reddy

  4558-4574

  • PDF

• An investigation into tapping of Al6061/SiC metal matrix composite with straight flute HSS machine tap

  Nagaraja ., Raviraja Adhikari, T. Yasir

  4575-4595

  • PDF

• Cutting tool wear progression index via signal element variance

  N. A. Kasim, M. Z. Nuawi, J. A. Ghani, M. Rizal, M. A. F. Ahmad, C. H. Che Haron

  4596-4612

  • PDF

• Effect of milling process on particle size, morphology and magnetization in non-stoichiometric Fe2O3-MnO2.

  P. Vera-Serna, M. A. Martínez-Sánchez, Martin Kusy, A. M. Bolarín-Miró, F. N. Tenorio-González, J. A. Juanico-Loran

  4613-4622

  • PDF

• Investigations on mechanical and wear behavior of nano Al2O3 particulates reinforced AA7475 alloy composites

  Madeva Nagaral, V. Auradi, S. A. Kori, Vijaykumar Hiremath

  4623-4635

  • PDF

• Co-pyrolysis of rubberwood sawdust (RWS) and polypropylene (PP) in a fixed bed pyrolyzer

  N. I. Izzatie, M. H. Basha, Y. Uemura, M. S. M. Hashim, M. Afendi, M. A. F. Mazlan

  4636-4647

  • PDF

• Effect of sintering temperature on density, hardness and tool wear for alumina-zirconia cutting tool

  A. B. Hadzley, T. Norfauzi, U. A. A. Umar, A. A. Afuza, M. M. Faiz, M. F. Naim

  4648-4660

  • PDF

• Development of a cutting edge temperature measurement of end mill tool by using infrared radiation technique

  M. A. Kiprawi, A. Yassin, A. M. N. A. Kamaruddin, S. T. S. Shazali, M. S. Islam, M. A. M. Said

  4661-4678

  • PDF

• An investigation of using grey scale image analysis for predicting the amount of deposited electrospun nanofibres

  A. H. Nurfaizey, F. C. Long, M. A. M. Daud, N. Muhammad, M. R. Mansor, N. Tucker

  4679-4692

  • PDF

• The effect of surface roughness of the impeller to the performance of pump as turbine pico power plant

  D. L. Zariatin, Dwi Rahmalina, Eko Prasetyo, A. Suwandi, M. Sumardi

  4693-4703

  • PDF

• Design and parametric characterization of flexure bearing as automotive valve spring replacement

  Mohd Razali Hanipah, Shahin Mansor, M. R. M. Akramin, Akhtar Razul Razali

  4704-4717

  • PDF

• A computational approach thermoelectric power generators to estimate heat flux

  Avijit Nayak, R. K. Nayak

  4718-4742

  • PDF

• Evaluation of the chemical and thermo-physical properties of locally aggregated kaolin-based refractory materials

  A. A. Olalere, S. S. Yaru, O. A. Dahunsi

  4743-4755

  • PDF