Energy Absorption Performance of A Rain Forest Vehicle under Frontal Impact
DOI:
https://doi.org/10.15282/jmes.6.2014.8.0078Keywords:
Finite element; crash analysis; crashworthiness; vehicle; simulation.Abstract
This paper presents a comprehensive numerical study of the crashworthy design of a rain forest vehicle (RFV) subjected to impact loading. A commercial finite element (FE) nonlinear code, LSDYNA, was employed to further evaluate the energy absorption performance of the structure under two crash scenarios; impacting a rigid wall and a rigid pole. The simulation results were used to identify the energy absorption capacity of the main subcomponent, thus facilitating crashworthiness requirements for future design improvements. The aims of this investigation were to enhance understanding of RFV behavior under impact loading and improve energy absorption capacity and safety, which will contribute towards the development of an early design stage of the RFV, and design and evaluation that may lessen the need for destructive full-scale testing. Recommendations and suggestions for improving the energy absorption capacity of RFVs have been made. A considerable improvement in energy absorption capacity has been obtained by inclusion of a supplementary device attached to the main chassis. These simplified provisions provide design guidelines that will considerably improve an operator’s chances of survival during an accidental impact in the forest.
References
Ahmad, Z., Nagel, G., & Thambiratnam, D. (2013). Inclusion of tapered tubes in enhancing the crash performance of automotive frontal structures. Key Engineering Materials, 553, 1-6.
Ahmad, Z., & Thambiratnam, D. P. (2009). Application of foam-filled conical tubes in enhancing the crashworthiness performance of vehicle protective structures. International Journal of Crashworthiness, 14(4), 349-363.
Cheng, Z. Q., Thacker, J. G., Pilkey, W. D., Hollowell, W. T., Reagan, S. W., & Sieveka, E. M. (2001). Experiences in reverse-engineering of a finite element automobile crash model. Finite Elements in Analysis and Design, 37(11), 843-860.
Clark, B. J., Thambiratnam, D. P., & Perera, N. J. (2008). Enhancing the impact energy absorption in roll over protective structures. International Journal of Crashworthiness, 13(2), 167-183.
Du Bois, P., Chou, C. C., Fileta, B. B., Khalil, T. B., King, A. I., Mahmood, H. F.et.al.Belwafa, J. E. (2004). Vehicle crashworthiness and occupant protection. Paper presented at the Automotive Applications Committee American Iron and Steel Institute, Southfield, Michigan.
Ghannam, M. Y., Niesluchowski, M., & Culkeen, P. M. (2002). Analysis of a frontal rail structure in a frontal collision: SAE Technical Paper.
Gursel, K. T., & Nane, S. N. (2010). Non-linear finite element analyses of automobiles and their elements in crashes. International Journal of Crashworthiness, 15(6),667-692.
Hong, S. W., Park, C. K., Mohan, P., Morgan, R. M., Kan, C. D., Lee, K.et al.Bae, H.(2008). A study of the iihs frontal pole impact test (Vol. 1): SAE Technical Paper.
Hu, H., Lu, W. J., & Lu, Z. (2011). Impact crash analyses of an off-road utility vehicle –part ii: Simulation of frontal pole, pole side, rear barrier and rollover impact crashes. International Journal of Crashworthiness, 17(2), 163-172.
Jenefeldt, F., & Thomson, R. (2004). A methodology to assess frontal stiffness to improve crash compatibility. International Journal of Crashworthiness, 9(5), 475-482.
Kamal, M., & Rahman, M. M. (2012). Study on dynamic behaviour of wishbone suspension system.
Kamal, M., Rahman, M. M., & Sani, M. S. M. (2013). Application of multibody simulation for fatigue life estimation. International Journal of Automotive and Mechanical Engineering, 7(1), 912-923.
Rahman, M. M., Ariffin, A. K., Abdullah, S., & Jamaludin, N. (2007). Finite element based durability assessment of a free piston linear engine component SDHM Structural Durability and Health Monitoring (Vol. 3, pp. 1-13).
Rahman, M. M., Ariffin, A. K., Jamaludin, N., Abdullah, S., & Noor, M. M. (2008). Finite element based fatigue life prediction of a new free piston engine mounting. Journal of Applied Sciences, 8(9), 1612-1621.
Rahman, M. M., Mohyaldeen, H. M., Noor, M. M., Kadirgama, K., & Bakar, R. A. (2011). Linear static response of suspension arm based on artificial neural network technique Advanced Materials Research (Vol. 213, pp. 419-426).
Thambiratnam, D. P., Clark, B. J., & Perera, N. J. (2008). Dynamic response of a rollover protective structure. Computer-Aided Civil and Infrastructure Engineering, 23(6), 448-464.
Yang, Y., Wu, X., & Hamada, H. (2013). Application of fibre-reinforced composites beam as energy absorption member in vehicle. International Journal of Crashworthiness, 18(2), 103-109.
Zaouk, A. K., Bedewi, N. E., Kan, C. D., & Marzougui, D. (1996). Development and evaluation of a c-1500 pickup truck model for roadside hardware impact simulation. Paper presented at the Proceedings of the FHWA Vehicle Crash Analysis Crash Conference, Mclean, VA.
