Utilisation of recycled thermoplastics sourced from rejected-unused disposable diapers as polymer blends

Authors

  • M.J. Taufiq Faculty of Mechanical Engineering, Universiti Teknikal Malaysia Melaka, 76100 Durian Tunggal, Melaka, Malaysia
  • Z. Mustafa Advanced Manufacturing Centre, Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, 76100 Durian Tunggal, Melaka, Malaysia
  • M.R. Mansor Faculty of Mechanical Engineering, Universiti Teknikal Malaysia Melaka, 76100 Durian Tunggal, Melaka, Malaysia

DOI:

https://doi.org/10.15282/jmes.11.4.2017.16.0282

Keywords:

Polypropylene/polyethylene blends; recycle; compression moulding; tensile properties; morphological properties.

Abstract

The blending of two or more thermoplastics could produce polymer blends, which are preferable compared to developing a new type of plastic. This paper presents the study on the utilisation of recycled thermoplastic polymers which are recovered from rejected unused disposable diapers. The aim of study is to characterise the effect of manufacturing temperature on the tensile and morphological properties of recycled plastic blend. Besides that, the polymer blend sourced from virgin materials was also prepared to compare the properties. The recycled and virgin materials were blended by using an internal mixer with fixed parameters. Later, the blended materials were crushed and moulded using hot compression moulding with temperature variations of 180 °C, 190 °C and 200 °C. The tensile tests were conducted in accordance with the ASTM D638 using a universal testing machine, followed by scanning electron morphological analysis. The results showed that as temperature increases, tensile strength decreases and tensile strain increases for both recycle and virgin blends. Tensile strength and strain for the recycled blend were also lower than the virgin blend at all temperatures, due to low miscibility in the recycled blend compared to the virgin one. The low miscibility caused more macrophase separation and resulted in poor adhesion between the polymer components. Also, the increase of temperature caused the tensile modulus to be reduced for the recycled blend. Meanwhile for the virgin blend, the modulus reduced at 190 °C but increased suddenly at temperature of 200 °C.

References

Bertin S, Robin J-J. Study and characterization of virgin and recycled LDPE/PP blends. European Polymer Journal. 2002;38:2255-64.

Strapasson R, Amico S, Pereira M, Sydenstricker T. Tensile and impact behavior of polypropylene/low density polyethylene blends. Polymer Testing. 2005;24:468-73.

Jereme IA, Siwar C, Alam MM. Waste Recycling in Malaysia: Transition from Developing to Developed Country. Indian Journal of Education and Information Management. 2015;4:1-14.

Espinosa-Valdemar RM, Turpin-Marion S, Delfín-Alcalá I, Vázquez-Morillas A. Disposable diapers biodegradation by the fungus Pleurotus ostreatus. Waste Management. 2011;31:1683-8.

Colón J, Ruggieri L, Sánchez A, González A, Puig I. Possibilities of composting disposable diapers with municipal solid wastes. Waste Management &and Research. 2011;29:249-59.

Weisbrod AV, Van Hoof G. LCA-measured environmental improvements in Pampers® diapers. The International Journal of Life Cycle Assessment. 2012;17:145-53.

ASTM S. D638: Standard test method for tensile properties of plastics. West Conshohocken (PA): ASTM International. 2010.

Brinson HF, Brinson LC. Characteristics, applications and properties of polymers. Polymer Engineering Science and Viscoelasticity: Springer; 2015. p. 57-100.

Dell'Erba R, Groeninckx G, Maglio G, Malinconico M, Migliozzi A. Immiscible polymer blends of semicrystalline biocompatible components: thermal properties and phase morphology analysis of PLLA/PCL blends. Polymer. 2001;42:7831-40.

Madi N. Thermal and mechanical properties of injection molded recycled high density polyethylene blends with virgin isotactic polypropylene. Materials & Design. 2013;46:435-41.

Hubo S, Delva L, Van Damme N, Ragaert K. Blending of recycled mixed polyolefins with recycled polypropylene: effect on physical and mechanical properties. AIP Conference Proceedings: AIP Publishing; 2016. p. 140006.

Downloads

Published

2017-12-31

How to Cite

[1]
M. Taufiq, Z. Mustafa, and M. Mansor, “Utilisation of recycled thermoplastics sourced from rejected-unused disposable diapers as polymer blends”, J. Mech. Eng. Sci., vol. 11, no. 4, pp. 3137–3143, Dec. 2017.

Similar Articles

1 2 3 4 5 6 7 8 9 10 > >> 

You may also start an advanced similarity search for this article.