An experimental study of the effect of the projection ratio and throat-aspect ratio on the efficiency and loss coefficient of a water jet pump
DOI:
https://doi.org/10.15282/jmes.15.3.2021.06.0650Keywords:
Water jet pump, throat-aspect ratio, projection ratio, efficiency, friction loss coefficientAbstract
This study focuses on the influence of dimensionless geometry parameters on the performance and loss coefficient of the throat and diffuser of the water jet pump apparatus. A water jet pump system was designed for a total of nine experimental cases with three different projection ratios and three throat-aspect ratios . The volumetric and pressure ratios - performance parameters are measured at a constant motive pressure and under varying backpressure. The efficiencies of the water jet pump in each configuration were assessed and compared. It was found that increasing 2 or 3 times of projection ratio degrades efficiency about 2% to 5.5%, respectively. Higher projection ratio ( > 1) expands the water jet diameter, which clogs the secondary flow. Hence, the changes in > 3 may have a significant impact on efficiency degradation. Shorter may cause the loss of kinetic energy in the diffuser, while longer reduces momentum transfer on the secondary flow. Moreover, the changes in and influence friction loss coefficient in the throat and diffuser section, and it reduces with increasing of volumetric ratio. It can be concluded that the appropriate value of projection ratio and throat-aspect ratio plays a role in the kinetic energy dissipation. It is also responsible for the location friction process, at a different volumetric ratio. However, the experimental results denoted the best efficiency and loss coefficient was achieved at a low projection ratio ( = 1) and small throat-aspect ratios ( = 5). The best efficiency of the study was about 23.37%.
References
I. E. L. Neto, ‘Maximum suction lift of water jet pumps’, J. Mech. Sci. Technol., vol. 25, no. 2, pp. 391–394, 2011, doi: 10.1007/s12206-010-1221-7.
ESDU, ESDU 85032 Ejectors and jet pumps Design and performance for incompressible liquid flow. Engineering Science Data Unit, 2007.
X. Long, H. Yao, and J. Zhao, ‘Investigation on mechanism of critical cavitating flow in liquid jet pumps under operating limits’, Int. J. Heat Mass Transf., vol. 52, no. 9, pp. 2415–2420, 2009, doi: https://doi.org/10.1016/j.ijheatmasstransfer.2008.11.018.
L. Xiao and X. Long, ‘Cavitating flow in annular jet pumps’, Int. J. Multiph. Flow, vol. 71, pp. 116–132, 2015, doi: https://doi.org/10.1016/j.ijmultiphaseflow.2015.01.001.
L. Z. Xiao, X. P. Long, Q. Lyu, Y. Hu, and Q. Q. Wang, ‘Numerical investigation on the cavitating flow in annular jet pump under different flow rate ratio’, IOP Conf. Ser. Earth Environ. Sci., vol. 22, no. 5, p. 52001, 2014, doi: 10.1088/1755-1315/22/5/052001.
X. Wang, Y. Chen, M. Li, Y. Xu, B. Wang, and X. Dang, ‘Numerical investigation of the cavitation performance of annular jet pumps with different profiles of suction chamber and throat inlet’, Eng. Appl. Comput. Fluid Mech., vol. 14, no. 1, pp. 1416–1428, Jan. 2020, doi: 10.1080/19942060.2020.1824875.
L. Xiao, X. Long, X. Li, Q. Zeng, and X. Yang, ‘Numerical investigation on the recirculation in annular jet pumps’, J. Mech. Sci. Technol., vol. 27, no. 6, pp. 1603–1609, 2013, doi: 10.1007/s12206-013-0406-2.
L. Xiao, X. Long, and J. Zhang, ‘Shear cavitation in an annular jet pump under recirculation conditions’, J. Fluids Eng., vol. 138, no. 6, Mar. 2016, doi: 10.1115/1.4032487.
M. P. Helios and W. Asvapoositkul, ‘Visualization of flow behavior and performance analysis of horizontal central-driven ejector system’, in 15th Asian Symposium on Visualization, 2019, pp. 1–11.
C. Prabkeao and K. Aoki, ‘Study on the optimum mixing throat length for drive nozzle position of the central jet pump’, J. Vis., vol. 8, no. 4, pp. 347–355, 2005, doi: 10.1007/BF03181554.
K. Aldaş and R. Yapıcı, ‘Investigation of effects of scale and surface roughness on efficiency of water jet pumps using CFD’, Eng. Appl. Comput. Fluid Mech., vol. 8, no. 1, pp. 14–25, Jan. 2014, doi: 10.1080/19942060.2014.11015494.
T. A. Meakhail and I. R. Teaima, ‘Experimental and numerical studies of the effect of area ratio and driving pressure on the performance of water and slurry jet pumps’, Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci., vol. 226, no. 9, pp. 2250–2266, Nov. 2011, doi: 10.1177/0954406211430458.
M. Nasr, M. A. Hosien, E. M. Wahba, and A. A. A. Sheha, ‘Computational and experimental study on the water-jet pump performance under different geometrical and operational parameters’, ERJ. Eng. Res. J., vol. 40, no. 2, pp. 107–117, 2017, doi: 10.21608/erjm.2017.66340.
A. H. Hammoud, ‘Effect of design and operational parameters on jet pump performance’, in 4th WSEAS International Conference on Fluid Mechanics and Aerodynamics, 2006, pp. 245–252.
A. A. Saker and H. Z. Hassan, ‘Study of the different factors that influence jet pump performance’, Open J. Fluid Dyn., vol. 3, no. 2, pp. 44–49, 2013, doi: 10.4236/ojfd.2013.32006.
S. R. Pandhare and A. K. Pitale, ‘Study the performance of water jet pump by changing the angle of mixing nozzle’, Int. J. Sci. Res. Sci. Technol., vol. 3, no. 3, pp. 538–540, 2017, doi: 10.32628/IJSRST1733189.
J. Toteff and M. Asuaje Tovar, ‘Design and multiparameter optimization of jet-pumps in a pipeline loops using CFD tools’, in 2nd Symposium on Development and Applications in Computational Fluid Dynamics, 2018, pp. 1–10, doi: 10.1115/FEDSM2018-83440.
A. A. A. Sheha, M. Nasr, M. A. Hosien, and E. M. Wahba, ‘Computational and experimental study on the water jet pump performance’, J. Appl. Fluid Mech., vol. 11, no. 4, pp. 1013–1020, 2018, doi: 10.18869/acadpub.jafm.73.247.28407.
J. Tang, Y. Zhou, J. Liu, J. Wang, and W. Zhu, ‘Liquid metal actuated ejector vacuum system’, Appl. Phys. Lett., vol. 106, no. 3, p. 031901, Jan. 2015, doi: 10.1063/1.4906098.
Y. I. Kryzhanivskyi and D. O. Panevnyk, ‘The study on the flows kinematics in the jet pump’s mixing chamber’, Geotech. Min. Mech. Eng. Mach. Build., vol. 1, pp. 62–68, 2019, doi: 10.29202/nvngu/2019-1/7.
J. Tang, Z. Zhang, L. Li, J. Wang, J. Liu, and Y. Zhou, ‘Influence of driving fluid properties on the performance of liquid-driving ejector’, Int. J. Heat Mass Transf., vol. 101, pp. 20–26, 2016, doi: https://doi.org/10.1016/j.ijheatmasstransfer.2016.04.028.
S. A. Gaade, M. M. Awad, A. R. Dohina, and W. M. El-Awady, ‘The performance of hybrid centrifugal-jet pump’, Int. J. Eng. Sci. Res. Technol., vol. 5, no. 11, pp. 484–490, 2016, doi: 10.5281/zenodo.168433.
M. Suzuki, K. Tanaka, and S. Sakuragi, ‘The operating characteristic of an underwater jet pump’, in 3rd IPEJ Conference on Research Achievements, 2016, pp. 1–4.
S. Zhao and S. Sakuragi, ‘Performance improvement of underwater jet pump by optimal arrangement of primary jet stream’, J. Fluid Sci. Technol., vol. 13, no. 1, pp. 1–11, 2018, doi: 10.1299/jfst.2018jfst0004.
S. Sakuragi and S. Zhao, ‘Operating characteristics of multi-injection type underwater jet pump’, Am. J. Mech. Appl., vol. 6, no. 3, pp. 58–67, 2018, doi: 10.11648/j.ajma.20180603.11.
R. G. Cunningham, ‘Liquid jet pumps for two-phase flows’, J. Fluids Eng., vol. 117, no. 2, pp. 309–316, Jun. 1995, doi: 10.1115/1.2817147.
N. L. Sanger, ‘An experimental investigation of several low-area-ratio water jet pumps’, J. Basic Eng., vol. 92, no. 1, pp. 11–19, Mar. 1970, doi: 10.1115/1.3424917.
A. E. Kroll, ‘The design of jet pumps’, Chem. Eng. Prog., vol. 1, no. 2, pp. 21–24, 1947.
J. M. A. Dandachi, ‘Steam air ejector performance and its dimensional parameters’, Ph.D. dissertation, Dept. Chem. Eng., Loughborough Univ., Loughborough, UK, 1990.
R. G. Cunningham, ‘Gas compression with the liquid jet pump’, J. Fluids Eng., vol. 96, no. 3, pp. 203–215, 1974, doi: 10.1115/1.3447143.
S. P. Mehta, ‘A study of water jet pumps’, M. S. Thesis, Dept. Mech. Eng., Kansas State Univ., Manhattan, USA, 1968.
A. H. Hammoud and A. A. Naby, ‘Slurry jet pump performance: under different Ddesign and operational parameters’, in 4th WSEAS International Conference on Fluid Mechanics and Aerodynamics, 2006, pp. 237–244.
I. A. El-Sawaf, M. A. Halawa, M. A. Younes, and I. R. Teaima, ‘Study of the different parameters that influence on the performance of water jet pump’, in 15th International Water Technology Conference, 2011, pp. 1–17.
T. A. Meakhail and I. R. Teaima, ‘A study of the effect of nozzle spacing and driving pressure on the water jet pump performance’, Int. J. Eng. Sci. Innov. Technol., vol. 2, no. 5, pp. 373–382, 2013.
H. Herwig and B. Schmandt, ‘Drag with external and pressure drop with internal flows: A new and unifying look at losses in the flow field based on the second law of thermodynamics’, Fluid Dyn. Res., vol. 45, no. 5, p. 55507, 2013, doi: 10.1088/0169-5983/45/5/055507.
B. R. Munson 1940-, Fundamentals of fluid mechanics. Seventh edition. Hoboken, NJ : John Wiley & Sons, Inc., [2013].
H. Herwig and B. Schmandt, ‘How to determine losses in a flow field: a paradigm shift towards the second law analysis’, Entropy, vol. 16, no. 6, 2014, doi: 10.3390/e16062959.
ESDU, ESDU 93022 Ejector and jet pump: computer program for design and performance for liquid Flow. Engineering Science Data Unit, 2011.
Test uncertainty PTC 19.1 - 2005. ASME, 2007.
S. Kline, ‘Describing uncertainties in single-sample experiments’, Mech. Eng., vol. 75, pp. 3–8, 1953.
Downloads
Published
Versions
- 2021-09-19 (2)
- 2021-09-19 (1)
How to Cite
Issue
Section
License
Copyright (c) 2021 Universiti Malaysia Pahang Publishing
This work is licensed under a Creative Commons Attribution 4.0 International License.
