Vol. 13 No. 2 (2019): (June 2019)

Article

• A comprehensive study on the buckling behaviour of woven composite plates with major aerospace cutouts under uniaxial loading

  S. B. Rayhan

  4756 - 4776

  • pdf

• Computational performance of a-100 kW low pressure turbine to recover gas turbine exhaust energy

  A. A. Ahmad Zahidin, A. M. I. Mamat, A. Romagnoli

  4777 - 4793

  • pdf

• Study of the microhardness and erosive wear behavior of organo-modified nanoclay filled glass-epoxy composites and optimization

  Z. Shanti Kiran, V. Suresh Babu, K. V. L. Soma Shekar

  4794 - 4815

  • pdf

• Compare the forecasting method of artificial neural network and support vector regression model to measure the bullwhip effect in supply chain

  E. Fradinata, S. Suthummanon, W. Suntiamorntut, Muhamad Mat Noor

  4816 - 4834

  • pdf

• Effect of orifice geometry and orifice to test section spacing on distribution of wall static pressure on a convex surface

  Anilkumar M. Hanchinal, Vadiraj V. Katti

  4835 - 4845

  • pdf

• Effects of ColdArc welding parameters on the tensile strengths of high strength steel plate investigated using the Taguchi approach

  S. D. Sabdin, N. I. S. Hussein, M. K. Sued, M. S. Ayob, M. A. S. A. Rahim, M. Fadzil

  4846 - 4856

  • pdf

• Effect of solution treatment on the microstructure and mechanical properties of Ti-6Al-6Mo hot-rolled alloy

  Alfirano ., S. S. Friandani, C. Sutowo

  4857 - 4868

  • pdf

• Role of nanoadditive blended biodiesel emulsion fuel on the performance and emission characteristics of diesel engine

  S. Rajesh Kumar, P. Sai Chaitanya

  4869 - 4879

  • pdf

• Thermal study of fluid flow inside an annular pipe filled with porous media under local thermal non-equilibrium condition

  Abdelkrim Bouaffane, Kamel Talbi

  4880 - 4897

  • pdf

• Thermo-mechanical properties of fused borosilicate syntactic foams

  Z. Salleh, M. M. Islam, J. A. Epaarachchi, M. T. I. Khan

  4898 - 4910

  • pdf

• Influence of process parameters on surface roughness and forming time of Al-1100 sheet in incremental sheet metal forming

  Swagatika Mohanty, Srinivasa Prakash Regalla, Yendluri Venkata Daseswara Rao

  4911 - 4927

  • pdf

• Multiaxial fatigue analysis for the shaft of a 100 MW hydro-power generator

  C. A. Mantilla, J. A. Valdés, F. Casanova

  4928 - 4945

  • pdf

• Alternative scheme for frequency response function measurement of experimental-analytical dynamic substructuring

  W. I. I. Wan Iskandar Mirza, M. N. Abdul Rani, M. A. Yunus, R. Omar, M. S. Mohd Zin

  4946 - 4957

  • pdf

• Effect of pH condition during hydrothermal synthesis on the properties of hydroxyapatite from eggshell waste

  A. R. Toibah, F. Misran, A. Shaaban, Z. Mustafa

  4958 - 4969

  • pdf

• On the use of nano fibrillated kenaf cellulose fiber as reinforcement in polylactic acid biocomposites

  Q. Ahsan, T. S. S. Carron, Z. Mustafa

  4970 - 4988

  • pdf

• Optimization of physical and mechanical properties of glycerol - modified natural rubber/starch - filled carbon black composites using two level factorial design

  M. Mazliah, N. Mohamad, H. E. Ab Maulod, A. R. Jeefferie, M. A. A. Mohd Abid, K. I. Karim, M. A. Mahamood, M. M. Hamdan

  4989 - 5005

  • pdf

• Effect of uniaxial load on microstructure and mechanical properties of Thixo-joint AISI D2 tool steel

  F. Adnan, Z. Sajuri, M. Z. Omar

  5006 - 5020

  • pdf

• Statistical analysis of second repair welding on dissimilar material using Taguchi method

  N. I. S. Hussein, S. Laily, M. S. Salleh, M. N. Ayof

  5021 - 5030

  • pdf

• The effect of vehicle weight on the sound produced by transverse rumble strips

  Z. Haron, N. Darus, K. Yahya, N. Mashros, Z. Jahya, M. A. Hezmi, H. Halim, M. H. Othman

  5031 - 5047

  • pdf

• Fatigue life assessment of welded joints in a crane boom using different structural stress approaches

  Brahami Riad, Hamri Okba, Sfarni Samir

  5048 - 5073

  • pdf

• Fatigue crack analysis of ferrite material by acoustic emission technique

  Md. T. I. Islam Khan, A. A. Rashid, R. Hidaka, N. Hattori, Md. M. Islam

  5074 - 5089

  • pdf

• Effect of copper based filler composition on the strength of brazed joint

  A. J. Sulaiman H., W. N. W. M. N. Hissyam, Aiman M. H., M. Ishak, T. Ariga

  5090 - 5103

  • pdf

• Surface roughness effect on droplet impact characterization: Experimental and theoretical study

  J. Zohrabi Chakaneh, S. M. Javid, M. Passandideh-Fard

  5104 - 5125

  • pdf

• Study on abrasive water jet drilling for graphite filled glass/epoxy laminates

  Deepak D., Ashwin Pai K.

  5126 - 5136

  • pdf

• Effect of initial blank temperature in hot press forming towards 22MnB5 springback failure

  C. H. Ng, C. F. Lai, S. N. M. Yahaya, S. Shamsudin, S. N. A. S. Ahmad, F. Sharrifuddin

  5137 - 5149

  • pdf

• Adaptive sliding mode control of a novel cable driven robot model

  F. Inel, S. Babesse

  5150 - 5162

  • pdf

• Experimental investigation of multiphase separation in different flow regimes through T-junction with an expander section

  Z. Q. Memon, W. Pao, F. Hashim, S. Ahmed

  5163 - 5181

  • pdf

• A review on thermo-physical properties and heat transfer applications of single and hybrid metal oxide nanofluids

  W. H. Azmi, S. N. M. Zainon, K. A. Hamid, R. Mamat

  5182 - 5211

  • pdf