Fatigue Life and Stress Analysis of a Single Cylinder Four Stroke Crankshaft
DOI:
https://doi.org/10.15282/ijame.21.3.2024.19.0902Keywords:
Crankshaft, Fatigue life, Finite element, ADAMS view, Weight optimizationAbstract
This paper focuses on the optimization of a crankshaft using ANSYS software in terms of weight and strength. The initial designs of the crankshaft, piston, and connecting rod were created using SolidWorks. The force generated by the gas during the combustion process was calculated to be 12017 N. Next, the SolidWorks assembled system was imported into ADAMS View software for simulation, which revealed a time-variant force of the crankpin of 14049 N. The calculated value was verified with results obtained from analytical calculations, showing a deviation of 0.23%. Finite element analysis was done for the crankshaft using ANSYS transient structural after applying loadings and boundary conditions. The optimization process aimed to minimize the crankshaft's weight while maintaining its strength and durability. The results of the ANSYS simulations showed a weight reduction of 2.5% from the original 2.983 kg to 2.907 kg, while maintaining the required strength and durability. The optimized crankshaft was compared to its original design in terms of fatigue life, weights, and stresses. The maximum von Mises stress was reduced by 16%, shear stress by 3.5%, and deformation by 3.5%, which were validated through analytical calculations. The crankshaft analysis resulted in a significant increase in fatigue life, calculated to be infinite under the given conditions. To conclude, the objective to optimize the crankshaft for performance and efficiency was achieved, demonstrating a 2.5% weight reduction and substantial improvements in fatigue life and stress distribution, proving the effectiveness of ANSYS software for the design optimization process.
References
S. Pal and K.S. Surendra, “Experimental investigation on cycle time in machining of forged crankshaft,” Materials Today, vol. 44, pp. 1469–1472, 2021.
G. Ramesh, M. Dora Babu, R. Satheesh and M. Kumar, “Design static and modal analysis of crankshaft,” International Journal of Creative Research Thoughts, vol. 6, pp. 254–261, 2018.
M.C. Priyanka, and R.H. Shinde, “Design & analysis of crankshaft for single cylinder diesel engine,” International Research Journal of Engineering and Technology, vol. 8, pp. 1311–1319, 2021.
M. Fonte, V. Infante, M.J. Freitas and L. Reis, “Failure mode analysis of two diesel engine crankshafts,” Procedia Structural Integrity, vol. 1, pp. 313-318, 2016.
K. Aliakbari, N. Safarzadeh and S.S. Mortazavi, “Analysis of the crankshaft failure of wheel loader diesel engine,” International Journal of Engineering, vol. 31, no. 3, pp. 473-479, 2018.
V. Mallikarjuna, B.J. Prasad and G. Kishore, “Design and finite element analysis of crank shaft by using catia and Ansys,” SSRG International Journal of Mechanical Engineering, vol. 4, pp. 8-18, 2017.
S. Manpreet and P.D. Dhiraj, “Materials comparison for crankshaft in Ansys,” International Journal of Management, Technology and Engineering, vol. 9, pp. 410–414, 2019.
B. Chiliński1 and M. Zawisza, " Analysis of bending and angular vibration of the crankshaft with a torsional vibrations damper," Journal of Vibroengineering, vol. 18, pp. 492-504, 2016.
Anish, “Reasons for failure and misalignment of crankshaft in marine engines,” [online] [cited 2019]. Available at: https://www.marineinsight.com/main-engine/reasons-for-failure-and-misalignment-of-crankshaft-in-marine-engines/
A. Arshad, C. Pengbo, A.A.E. Elmenshawy and B. Ilmars, “Design optimization for the weight reduction of 2-cylinder reciprocating compressor crankshaft,” Achieve of Mechanical Engineering, vol. 68, pp. 281–286, 2021.
Y.Z. Ang and P.X. Ku, “Study on failure analysis of crankshaft using finite element analysis,” MATEC Web of Conferences 335, vol. 335, pp. 233–239, 2021.
L. Witek, M. Sikora, F. Stachowicz and T. Tomasz, “Stress and failure analysis of the crankshaft of diesel engine,” Engineering Failure Analysis, vol. 82 pp. 703–712, 2017.
V. Sowjanya, and C. Raghunatha Reddy, “Design and analysis of a crank shaft,” International Journal of Engineering Science and Computing, vol. 6, pp. 3814-3821, 2017.
S. Mahendrakar and P.R. Kulkarni, “A review on design and vibration analysis of a crank shaft by FEA and experimental approach,” International Journal of Scientific Development and Research, vol. 1, pp. 146–149, 2017.
V.C. Shahane and R.S. Pawar, “A review on finite element analysis of the crankshaft of internal combustion engine,” International Research Journal of Engineering and Technology, vol. 3, pp. 1658–1663, 2016.
G. Gopal, L.S. Kumar, K.V.B. Reddy, M.U.M. Rao and G. Srinivasulu, “Analysis of piston, connecting rod and crank shaft assembly,” Materials Today: Proceedings, vol. 4, pp. 7810–7819, 2017.
M. Degefe, P. Paramasivam, D. Tamana and K. Venkatesh, “Optimization and finite element analysis of single cylinder engine crankshaft for improving fatigue life,” American Journal of Mechanical and Materials Engineering, vol. 1, pp. 58–68, 2017.
M.N. Pratiksha, “Analysis of crankshaft,” International Journal of Scientific Engineering and Research, vol. 5, pp. 2347–3878, 2017.
B.G. Nandkumar, Z.S. Bhaskar and P.A. Ramesh, “Design, optimization and finite element analysis of crankshaft,” International Journal of Innovation in Engineering, Research and Technology,
P.Thejasree, K.D. Kumar and S.L.P. Lakshmi, “Modelling and analysis of crankshaft for passenger car using Ansys,” Materials Today: Proceedings, vol. 4, pp. 11292–11299, 2017.
B.V. Ramnath, C. Elanchezhian, J. Jeykrishnan, R. Ragavendar, P.K. Rakesh, J.S Dhamodar and A. Danasekar, “Implementation of reverse engineering for crankshaft manufacturing industry,” Materials Today: Proceedings, vol. 5, pp. 994–999, 2018.
R. Pradhan and S. Puhan, “Analysis and optimization of crankshaft for a single cylinder four stroke SI engine,” Journal of Emerging Technologies and Innovative Research, vol. 5, pp. 246–249, 2018.
K.P. Durga, V.J.P. Narayana and N. Kiranmaye, “Design and stress analysis of crankshaft for single cylinder four stroke diesel engine,” International Journal of Engineering Research & Technology, vol. 7, pp. 154-159, 2018.
I.T. Jiregna, G.G. Sirata and F.T. Soramo, “Fatigue failure analysis of crankshafts - A review,” International Journal of Innovative Science, Engineering and Technology, vol. 7, pp. 93–106, 2020.
P. Citti, A. Giorgetti and U. Millefanti, “Current challenges in material choice for high-performance engine,” International Conference on Stress Analysis, vol. 8, pp. 486–500, 2018.
K. Satyanarayana, A.K. Viswanath, T.V. Hanumanta Rao and S.V. Uma Maheswara Rao, “Investigation of the stresses induced in crank shaft AISI E4340 forged steel,” 11th International Symposium on Plasticity and Impact Mechanics, Procedia Engineering, vol. 173, pp. 1672–1677, 2017.
P. Mishara and S. Sinha, "Stress analysis and topology optimization of connecting rod of two wheelers using FEA," International Journal of Mechanical Technology, vol. 9, pp. 559–568, 2018.
A. Muhammad and I.H. Shanono, “Static analysis and optimization of a connecting rod,” International Journal of Engineering Technology and Sciences, vol. 6, pp. 24-40, 2019.
S.N. Kurbet, V.V. Kuppast and T. Basavaraj, “Material testing and evaluation of crankshafts for structural analysis,” Materials Today: Proceedings, vol. 34, pp. 556-562, 2021.
T. Nageswara Rao, K. Vasudev Rao, V. Ananta Rahul, G. Rajesh, and S.S. Sowgandh, “Analysis and Optimization of Gas/petrol Engine Components,” International Journal of Latest Technology in Engineering, Management & Applied Science, vol. 7, pp. 230-236, 2018.
L. Karthick, N. Mallireddy, J. Yogaraja, S. Sivakumar, and A. Sasikumar, “Modelling and analysis of an EN8 crankshaft material in comparison with Forged steel crankshaft,” Materials Today: Proceedings, vol. 47, pp. 6168-6172, 2021.
S.S. Mohtasebi, H. Afshari and H. Monili, “Analysis of crankshafts vibrations to compare the dynamic behavior of steel and cast iron crankshafts,” Journal of Applied Sciences, vol. 6, pp. 591-594, 2006.
K. Sandya, M. Keerthi and K. Srinivas, “Modelling and stress analysis of crankshaft using FEM package Ansys,” Journal of Emerging Technologies and Innovative Research, vol. 6, pp.378-383, 2019.
R. Hamel, L. Mustapha and B. Benyebka, “Elasto-hydrodynamic lubrication analysis of a porous misaligned crankshaft bearing operating with nanolubrications,” Mechanics & Industry, vol. 24, 2022.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 The Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.