Performance Characteristics of a Compact Core Annular-Radial Magnetorheological Damper for Vehicle Suspension Systems

Ahmad Zaifazlin Zainordin; Zamri Mohamed

doi:10.15282/ijame.21.4.2024.3.0906

Authors

Ahmad Zaifazlin Zainordin Department of Mechanical Engineering, Politeknik Sultan Haji Ahmad Shah, 25350 Kuantan, Pahang, Malaysia
Zamri Mohamed Faculty of Mechanical and Automotive Engineering Technology, Universiti Malaysia Pahang Al-Sultan Abdullah, 26600 Pahang, Malaysia

DOI:

https://doi.org/10.15282/ijame.21.4.2024.3.0906

Keywords:

Magnetorheological fluid, Magnetorheological damper, Flow rate, Velocity, Valve

Abstract

The magnetorheological (MR) damper is a by-wire system capable of providing variable damping stiffness by responding to an apparent magnetic field. In response to the magnetic field application, the magnetorheological fluid (MR fluid) exhibited altered behavior within the damper. Typically, a damper’s internal and external valves operate in flow mode, where the flow is regulated by controlling the magnetic field. This study aims to investigate the performance characteristics of a small core annular and radial magnetorheological valve (SCARMV) designed for applications in vehicle suspension systems. The proposed design of the simplified MR valve is based on a meandering-type valve composed of multiple valve cores that have been simplified to a single core. Dynamic testing was performed on the proposed valve, which features a single rod tube damper, to investigate the damping force characteristics by varying currents and frequencies. The characteristics of the measured damping force were compared to the calculated damping force based on the pressure drop calculation and the FEMM simulation of magnetic flux. By increasing the stroke length of the valve travel is set to 10 mm at a current input of 0 A to 1.0 A, the maximum output of the MR valve damping force was approximately 1.57 kN. In addition, a mathematical model of SCARMV is presented and compared to the experimental data. Therefore, based on the experimental results, it was concluded that the usability of a compact core MR valve is reliable. However, more in-depth studies are required before these dampers can be applied to vehicle suspension systems.

References

[1] Y. Shiao, W.H. Kuo, Q.A. Nguyen, and C.W. Lai, “Development of a variable-damping magnetorheological damper with multiple poles,” Journal of Vibroengineering, vol. 17, no. 3, pp. 1071–1078, 2015.

[2] X.-X. Bai, W. Hu, and N.M. Wereley, “Magnetorheological damper utilizing an inner bypass for ground vehicle suspensions,” IEEE Transactions on Magnetics, vol. 49, no. 7, pp. 3422–3425, 2013.

[3] B. Lei, J. Li, W. Zhou, M. Shou, F. Zhao, and C. Liao, “Dual-stage theoretical model of magnetorheological dampers and experimental verification,” Smart Materials and Structures, vol. 33, no. 4, p. 045027, 2024.

[4] S. Sun, X. Tang, J. Yang, D. Ning, H. Du, S. Zhang et al., “A new generation of magnetorheological vehicle suspension system with tunable stiffness and damping characteristics,” IEEE Transactions on Industrial Informatics, vol. 15, no. 8, pp. 4696–4708, 2019.

[5] T. Xu, H. Wang, Y. Li, D. Leng, and H. Xu, “Full vehicle experimental testing of semi-active suspension equipped with magnetorheological dampers,” in 2023 IEEE/ASME International Conference on Advanced Intelligent Mechatronics (AIM), pp. 495–500, 2023.

[6] G. Hu, Q. Liu, R. Ding, and G. Li, “Vibration control of semi-active suspension system with magnetorheological damper based on hyperbolic tangent model,” Advances in Mechanical Engineering, vol. 9, no. 5, 2017.

[7] H.X. Ai, D.H. Wang, and W.H. Liao, “Design and modeling of a magnetorheological valve with both annular and radial flow paths,” Journal of Intelligent Material Systems and Structures, vol. 17, no. 4, pp. 327–334, 2006.

[8] F. Imaduddin, S.A. Mazlan, H. Zamzuri, and I.I.M. Yazid, “Design and performance analysis of a compact magnetorheological valve with multiple annular and radial gaps,” Journal of Intelligent Material Systems and Structures, vol. 26, no. 9, pp. 1038–1049, 2013.

[9] A. Grunwald and A.G. Olabi, “Design of magnetorheological (MR) valve,” Sensors and Actuators A: Physical, vol. 148, no. 1, pp. 211–223, 2008.

[10] G. Liu, F. Gao, D. Wang, and W.-H. Liao, “Medical applications of magnetorheological fluid: A systematic review,” Smart Materials and Structures, vol. 31, no. 4, p. 043002, 2022.

[11] T.R.G. Chary, M. Allaparthi, S. Dusa, P. Suryapet, and D. Tarun, “Properties, applications, defects, and failures of magnetorheological fluids,” in Intelligent Manufacturing and Energy Sustainability, Singapore: Springer Nature Singapore, pp. 517–528, 2024.

[12] H. Eshgarf, A. Ahmadi Nadooshan, and A. Raisi, “An overview on properties and applications of magnetorheological fluids: Dampers, batteries, valves and brakes,” Journal of Energy Storage, vol. 50, p. 104648, 2022.

[13] J. Rabinow, “The magnetic fluid clutch,” Electrical Engineering, vol. 67, no. 12, p. 1167, 1948.

[14] X. Tang, X. Zhang, R. Tao, and Y. Rong, “Structure-enhanced yield stress of magnetorheological fluids,” Journal of Applied Physics, vol. 87, no. 5, pp. 2634–2638, 2000.

[15] S. Pisetskiy and M.R. Kermani, “A concept of a miniaturized MR clutch utilizing mr fluid in squeeze mode,” in 2020 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pp. 6347–6352, 2020.

[16] D. Kumar, G.A. Harmain, G. Gaurav, K.P. Lijesh, B. Kuriachen, H. Hirani et al., “A novel seal design to enhance MR brake performance,” Transactions of the Indian Institute of Metals, vol. 76, no. 9, pp. 2335–2342, 2023.

[17] S. Khuntia, R. Yadav, R.C. Singh, and V. Rastogi, “Design, development and analysis of a magnetorheological damper,” IOP Conference Series: Materials Science and Engineering, vol. 804, no. 1, p. 012009, 2020.

[18] S. Chen, R. Li, P. Du, H. Zheng, and D. Li, “Parametric modeling of a magnetorheological engine mount based on a modified polynomial bingham model,” Frontiers in Materials, vol. 6, 2019.

[19] A.Z. Zainordin, Z. Mohamed, and F. Ahmad, “Magnetorheological fluid: Testing on automotive braking system,” International Journal of Automotive and Mechanical Engineering, vol. 18, no. 1, pp. 8577–8584, 2021.

[20] P. Raja, X. Wang, and F. Gordaninejad, “A high-force controllable MR fluid damper–liquid spring suspension system,” Smart Materials and Structures, vol. 23, no. 1, p. 015021, 2014.

[21] Y.K. Lau and W.H. Liao, “Design and analysis of magnetorheological dampers for train suspension,” Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, vol. 219, no. 4, pp. 261–276, 2005.

[22] Y.-J. Park, B.-H. Kang, and S.-B. Choi, “A new rotary magnetorheological damper for a semi-active suspension system of low-floor vehicles,” Actuators, vol. 13, no. 4, p. 155, 2024.

[23] X. Ye, J. Dong, B. Wu, O. Qing, J. Wang, and G. Zhang, “Design and modeling of a double rod magnetorheological grease damper,” Journal of Mechanical Science and Technology, vol. 38, no. 8, pp. 4065–4075, 2024.

[24] X. Zhu, X. Jing, and L. Cheng, “Magnetorheological fluid dampers: A review on structure design and analysis,” Journal of Intelligent Material Systems and Structures, vol. 23, no. 8, pp. 839–873, 2012.

[25] W. Kordonski, S. Gorodkin, and A. Kolomentsev, “Magnetorheological valve and devices incorporating magnetorheological elements,” Patent No. 5353839, 1994.

[26] S. Gorodkin, A. Lukianovich, and W. Kordonski, “Magnetorheological throttle valve in passive damping systems,” Journal of Intelligent Material Systems and Structures, vol. 9, no. 8, pp. 637–641, 1998.

[27] S. Yokota, K. Yoshida, and Y. Kondoh, “A pressure control valve using MR fluid,” in Proceedings of the JFPS International Symposium on Fluid Power, Tokyo, pp. 377–380, 1999.

[28] K. Yoshida, H. Takahashi, S. Yokota, M. Kawachi, and K. Edamura, “A bellows-driven motion control system using a magnetorheological fluid,” Proceedings of the JFPS International Symposium on Fluid Power, vol. 2002, no. 5–2, pp. 403–408, 2002.

[29] D.H. Wang, H.X. Ai, and W.H. Liao, “A magnetorheological valve with both annular and radial fluid flow resistance gaps,” Smart Materials and Structures, vol. 18, no. 11, p. 115001, 2009.

[30] B. Ichwan, S.A. Mazlan, F. Imaduddin, Ubaidillah, T. Koga, and M.H. Idris, “Development of a modular MR valve using meandering flow path structure,” Smart Materials and Structures, vol. 25, no. 3, p. 037001, 2016.

[31] G. Hu, H. Liu, J. Duan, and L. Yu, “Damping performance analysis of magnetorheological damper with serial-type flow channels,” Advances in Mechanical Engineering, vol. 11, no. 1, p. 1687814018816842, 2019.

[32] M.H. Idris, F. Imaduddin, Ubaidillah, S.A. Mazlan, and S.-B. Choi, “A concentric design of a bypass magnetorheological fluid damper with a serpentine flux valve,” Actuators, vol. 9, no. 1, p. 16, 2020.

[33] S. Sgobba, “Physics and measurements of magnetic materials,” in CERN Accelerator School: Course on Magnets, p. 25, 2011.

[34] Lord Corp, “MRF-132DG Magnetorheological Fluid,” Lord Technical Data, vol. 54, no. 2, p. 11, 2011.

[35] B. Ichwan, S.A. Mazlan, F. Imaduddin, H. Zamzuri, and M.A.A. Rahman, “Design and performance analysis of magnetorheological valve module with annular-radial concept,” ARPN Journal of Engineering and Applied Sciences, vol. 10, no. 17, pp. 7743–7748, 2015.

[36] Q.-H. Nguyen, S.-B. Choi, and N.M. Wereley, “Optimal design of magnetorheological valves via a finite element method considering control energy and a time constant,” Smart Materials and Structures, vol. 17, no. 2, p. 025024, 2008.