Analysis on Auger Pump Performance During Handling High Viscous Liquid

Authors

  • E. Alisha Faculty of Manufacturing and Mechatronic Engineering Technology, Universiti Malaysia Pahang, 26600 UMP Pekan, Pahang, Malaysia
  • N. Najwa Faculty of Manufacturing and Mechatronic Engineering Technology, Universiti Malaysia Pahang, 26600 UMP Pekan, Pahang, Malaysia
  • A.S. Jamaludin Faculty of Manufacturing and Mechatronic Engineering Technology, Universiti Malaysia Pahang, 26600 UMP Pekan, Pahang, Malaysia
  • M. N. M. Razali Faculty of Manufacturing and Mechatronic Engineering Technology, Universiti Malaysia Pahang, 26600 Pahang, Malaysia
  • S.N.B.M. Saffe Faculty of Manufacturing and Mechatronic Engineering Technology, Universiti Malaysia Pahang, 26600 UMP Pekan, Pahang, Malaysia

DOI:

https://doi.org/10.15282/jmmst.v6i2.8564

Keywords:

Auger Screw Pump, Viscous Liquid, Liquid supply pressure

Abstract

Viscosity is one of the factors affecting the performance of the auger pump. An auger pump is positive-displacement (PD) pump that moves fluids and semi-solid material along the screw axis using one or more screws. The study is about the analysis of the performance of the auger pump when transferring various viscosity liquids. In the study, a pumping device with auger shaft is designed. The sample liquids chosen for the experiment oil and concentrated detergent that poses various viscosity. The viscosity is being identified roughly by Zahn Cup Method with the temperature kept constant at 26°C throughout the measurement. The performance of the auger pump can be accessed by altering the motor speed in order to get various reading for the flow rate and pressure. It is found in the study; flowrate is affected by viscosity with the increasing motor speed. The study proves that the auger pump can operate with viscosity of 770 cSt liquid.

References

A. M. Rosli, N. Jamil, A. S. Jamaludin, M. N. Razali, and A. R. Yusoff, “Tool wear observation during unconventional low speed machining using low cost micromilling,” Lecture Notes in Mechanical Engineering, pp. 589–597, 2021.

A. M. Rosli, A. S. Jamaludin, M. N. Razali, A. S. Sani, S. B. Hamzah, and M. S. Osman, “Modelling of Fuzzy Inference System for micro milling—a preliminary study through FEM,” Lecture Notes in Mechanical Engineering, pp. 445–456, 2019.

A. S. Jamaludin, H. Akira, T. Furumoto, T. Koyano, and Y. Hashimoto, “High precision estimation on physical behavior for cutting with various tool rake angle by finite element method,” Lecture Notes in Mechanical Engineering, pp. 715–723, 2018.

A. S. Jamaludin, A. Hosokawa, T. Furumoto, T. Koyano, and Y. Hashimoto, “Study on the effectiveness of extreme cold mist MQL system on turning process of stainless steel AISI 316,” IOP Conference Series: Materials Science and Engineering, vol. 319, p. 012054, 2018.

N. H. Khairul Anuar, M. N. Mhd Razali, M. R. Mohamad Yasin, M. Abdul Hadi, and A. N. Abd. Ghaffar, “Study on custom centrifugal pump performance in supplying food based high viscos liquid,” Journal of Modern Manufacturing Systems and Technology, vol. 5, no. 1, pp. 80–88, 2021.

N. Sazali, A. S. Jamaludin, and N. H. Ngadiman, “A major review on tribology-based materials,” Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, vol. 71, no. 2, pp. 26–37, 2020.

N. Sazali, A. S. Jamaludin, and N. H. Ngadiman, “An essential studies on Tribology’s: A short review,” Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, vol. 72, no. 1, pp. 1–8, 2020. [8] I. N. Ibrahim, N. Sazali, A. S. Jamaludin, D. Ramasamy, S. M. Soffie, and M. H. D. Othman, “A Review on Vehicle Radiator Using Various Coolants”, J. Adv. Res. Fluid Mech. Therm. Sc., vol. 59, no. 2, pp. 330–337, Dec. 2020.

A. S. Amiril Sahab, J. Nor Athira, J. Ahmad Shahir, and T. Norfazillah, “Calophyllum-inophyllum from Pahang Malaysia as Biolubricant feedstock for industrial application,” Lecture Notes in Mechanical Engineering, pp. 441–449, 2021.

N. Boubekri and V. Shaikh, “Minimum quantity lubrication (MQL) in machining: Benefits and drawbacks,” Journal of Industrial and Intelligent Information, vol. 3, no. 3, 2014.

G. Di Giovine, L. Mariani, D. Di Battista, R. Cipollone, and F. Fremondi, “Modeling and experimental validation of a triple-screw pump for internal combustion engine cooling,” Applied Thermal Engineering, vol. 199, p. 117550, 2021.

K. E. Borisova, T. N. Ivanova, and R. G. Latypov, “Study of screw pump stator and rotor working capacity to increase the output,” Procedia Engineering, vol. 206, pp. 688–691, 2017.

Z.-L. Wang, H.-W. Shi, S.-Y. Wang, Z.-M. Wang, M.-M. Hao, and J. Wang, “Theoretical study on the pressurization characteristics of disc-seal single screw pump used in high viscosity oily sludge conveying field,” Petroleum Science, vol. 19, no. 3, pp. 1361–1370, 2022.

E. M. Ofuchi, J. M. C. Cubas, H. Stel, R. Dunaiski, T. S. Vieira, and R. E. M. Morales, “A new model to predict the head degradation of centrifugal pumps handling highly viscous flows,” Journal of Petroleum Science and Engineering, vol. 187, p. 106737, 2020.

Z. Liu, L. Zou, J. Qiao, C. Shi, and X. Liu, “The influence of the viscosity of crude oil on liquid-dynamic noise characteristics in the volute shell of oil transfer pump,” Measurement, vol. 197, p. 111285, 2022.

S. V. K., U. Subramaniam, R. Madurai Elavarasan, K. Raju, and P. Shanmugam, “Sensorless parameter estimation of VFD based Cascade Centrifugal pumping system using automatic pump curve adaption method,” Energy Reports, vol. 7, pp. 453–466, 2021.

M. Rossi, G. Comodi, N. Piacente, and M. Renzi, “Effects of viscosity on the performance of Hydraulic Power Recovery Turbines (hprts) by the means of computational fluid dynamics (CFD) simulations,” Energy Procedia, vol. 148, pp. 170–177, 2018.

M. Liu, L. Tan, and S. Cao, “Influence of viscosity on energy performance and flow field of a multiphase pump,” Renewable Energy, vol. 162, pp. 1151–1160, 2020.

R. Torabi and S. A. Nourbakhsh, “The effect of viscosity on performance of a low specific speed centrifugal pump,” International Journal of Rotating Machinery, vol. 2016, pp. 1–9, 2016.

K. Taylor, A. Post, T. B. Hoshizaki, and M. D. Gilchrist, “The effect of a novel impact management strategy on maximum principal strain for reconstructions of American football concussive events,” Proc. Inst. Mech. Eng. Part P J. Sport. Eng. Technol., vol. 233, no. 4, pp. 503–513, 2019.

Downloads

Published

30-09-2022

How to Cite

Alisha, E., Najwa, N., Jamaludin, A., Razali, M. N. M., & Saffe, S. (2022). Analysis on Auger Pump Performance During Handling High Viscous Liquid. Journal of Modern Manufacturing Systems and Technology, 6(2), 48–54. https://doi.org/10.15282/jmmst.v6i2.8564

Issue

Section

Articles