Vol. 13 No. 3 (2016): December

Articles

• A numerical–experimental approach to assess emission performance of new generation engines during the cold transient

  Paolo Iodice , Adolfo Senatore

  3599 - 3612

  • PDF

• An experimental study of the performance and emissions of spark ignition gasoline engine

  Adnan Kadhim Rashid, Mohd Radzi Abu Mansor, Wan Aizon Wan Ghopa, Zambri Harun, Wan Mohd Faizal Wan Mahmood

  3540 - 3554

  • PDF

• Dynamic simulation of brake pedal force effect on heavy vehicle braking distance under wet road conditions

  M. Zamzamzadeh , A.A. Saifizul, R. Ramli, M.F. Soong

  3555 - 3563

  • PDF

• A study on the damage evolution of P91 steel under cyclic loading at high temperature

  A.A. Saad , Z. Bachok, W. Sun

  3564 - 3573

  • PDF

• Correlation between vertical wheel impact energy with lateral wheel impact energy: A finite element analysis approach

  H. Zainuddin, M.B. Ali , N.B. Muhammad Said, K.A. Zakaria, K.A. Zakaria

  3574 - 3583

  • PDF

• Fatigue damage monitoring using un-supervised clustering method of acoustic emission signal on SAE 1045 steel

  M. Mohammad , A. Tajuddin, S. Abdullah, N. Jamaluddin, B.I.S. Murat

  3584 - 3598

  • PDF

• A mathematical model of the apparent mass of the human body under fore-and-aft whole-body vibration

  N. Nawayseh

  3613 - 3627

  • PDF

• Damaging fatigue cycles determination for random service loadings using mixed Weibull analysis

  M. Mahmud, S. Abdullah , M.F.M. Yunoh, A.K. Ariffin , Z.M. Nopiah

  3628 - 3641

  • PDF

• Evaluation of eco-design strategies for development of multiple life-cycle products

  T.F. Go, D.A. Wahab , H. Hishamuddin

  3642 - 3656

  • PDF

• Energy absorption capability and deformation of laminated panels for armoured vehicle materials

  N.A. Rahman, S. Abdullah , M.F. Abdullah, W.F.H. Zamri, M.Z. Omar , Z. Sajuri

  3657 - 3668

  • PDF

• Optimisation of process parameters for minimum volumetric wear rate on AA7075-TiC metal matrix composite

  V. RamakoteswaraRao , N. Ramanaiah, M. Srinivasa Rao, M.M.M. Sarcar , G. Kartheek

  3669 - 3680

  • PDF

• Hydrogen mixture with gasoline for conventional motorcycles and effect on mass flow rate, brake thermal efficiency and emissions

  H. Razali , K. Sopian, S. Mat, M.R.A. Mansor , N. Amon

  3681 - 3695

  • PDF

• Pressure sores of human tissue damage during pelvic binder compression

  I. Munandar , S. Huzni, M.S. Ismail , M.S. Shaari , A.K. Ariffin

  3696 - 3709

  • PDF

• Heat transfer performance of non-circular coiled tubes - Research summary, challenges and directions

  J.C. Kurnia , A.P. Sasmito

  3710 - 3727

  • PDF

• Propagation and scattering of guided waves in composite plates with defects

  Bibi I. S. Murat , P. Fromme

  3728 - 3741

  • PDF

• Mechanical properties and microstructures of steel panels for laminated composites in armoured vehicles

  W.N.M. Jamil, M.A. Aripin, Z. Sajuri , S. Abdullah, M.Z. Omar, M.F. Abdullah , W.F.H. Zamri

  3742 - 3753

  • PDF

• Investigation of convective heat transfer coefficient and initial temperature of waxy crude oil on the formation of voids

  Girma T. Chala , Shaharin A. Sulaiman, Shaharin A. Sulaiman, Azuraien Japper-Jaafar, Wan Ahmad Kamil Wan Abdullah

  3754 - 3762

  • PDF

• Mechanical properties of betel nut and glass fibre reinforced hybrid polyethylene composites

  M. Merajul Haque , Mahbub Hasan

  3763 - 3772

  • PDF

• The effect of injection timing on the performance and emission of direct injection CI engine running on diethyl ether-diesel blends

  K.R. Patil , S.S. Thipse, S.S. Thipse

  3773 - 3787

  • PDF

• Current trends on combustion control methods using fuel reactivities

  Ram Kishore Sankaralingam , T. Venugopal

  3788 - 3811

  • PDF